GVS CHTC-86/01.1.21 Скачать руководство пользователя страница 69

Страница: 69 / 89

GVS K-BUS

○

KNX/EIB

Thermostat

www.video-star.com.cn

[email protected]

Tel.

：

（

8620

）

39338986

Fax.

：（

8620

）

39338465

4.12.5

External temperature sensor for RTC

Parameter window "Input 4" is seen as Figure 4.12.6, Temperature sensor inputs can be connected

an external NTC thermistor, as an external temperature sensor of thermostat panel, or as a temperature

limiter of underfloor heating, to stop heating when the heating temperature is higher than the limit.

Figure 4.12.6 parameter window "Input 4"

Parameter "Function of input 4"

Options: No function

external temperature sensor for RTC

temperature limiter(underfloor heating)

If temperature sensor inputs is used as an external temperature sensor of thermostat panel, it

should be connected an external NTC thermistor, but also selects "external sensor" or "internal sensor

and external sensor" for "Temperature sensor “in "Measurement Settings".

Note:

if temperature

sensor input is used as an external temperature sensor, the communication object of external

temperature on the bus into the external temperature is invalid.

Parameter "Resistor of external temperature sensor"

Options: 1K

Содержание CHTC-86/01.1.21


























































































Результаты поиска

Содержание CHTC-86/01.1.21

Отзывы:

Похожие инструкции для CHTC-86/01.1.21

Бренды по названию

Популярные бренды

GVS CHTC-86/01.1.21, Руководство пользователя

Результаты поиска

Содержание CHTC-86/01.1.21

Отзывы:

Похожие инструкции для CHTC-86/01.1.21

Бренды по названию

Популярные бренды