GVS CHTC-86/01.1.21 Скачать руководство пользователя страница 51

Страница: 51 / 89

GVS K-BUS

○

KNX/EIB

Thermostat

www.video-star.com.cn

[email protected]

Tel.

：

（

8620

）

39338986

Fax.

：（

8620

）

39338465

Send following telegram cyclically

These two parameters are used to respectively set ways of sending telegram to the object

"1bit/1byte output, humidity", when the detected humidity is below the low threshold or above the high

threshold.

If select "do not send telegram", the object does not sends telegram;

If select "send following telegram once", the object sends telegram once;

If select "send cyclically", the object sends telegram cyclically, sending time can be set in the

following parameter "cycle time for humidity threshold value [min]" in the settings, you can send two

object types, the value of the object is set in the following parameters "logic1bit / 1byte telegram value ".

Parameter "logic 1 bit /1byte telegram value"

Options: Logic 1bit (0~1)

1byte

（

0~255

）

This parameter is used to specify, the telegram value that object "1bit/1byte output, humidity" sends,

when the current humidity is below the low threshold and above the high threshold.

After a bus reset

or programming, if the current humidity is between the low threshold and the high threshold, the object

does not send telegram to the bus.

Parameter "Cycle time for humidity threshold value [min](if used)"

Options: 1- 255

This parameter is used to set the object "1bit/1byte output, humidity" cycle time on the bus to send

the value of the interval, only when the parameter "If humidity is lower / upper than threshold value" set

loop send it to use.

Parameter "use block of the humidity threshold output"

Options: yes

This parameter sets whether to enable the threshold value, if enabled, the object "humidity

threshold value1 / 2 block" is visible, when the object receives telegram "1", threshold value is disabled,

when the object receives telegram "0", the threshold value is enabled.

Содержание CHTC-86/01.1.21


























































































Результаты поиска

Содержание CHTC-86/01.1.21

Отзывы:

Похожие инструкции для CHTC-86/01.1.21

Бренды по названию

Популярные бренды

GVS CHTC-86/01.1.21, Руководство пользователя

Результаты поиска

Содержание CHTC-86/01.1.21

Отзывы:

Похожие инструкции для CHTC-86/01.1.21

Бренды по названию

Популярные бренды