GVS CHTC-86/01.1.21 Скачать руководство пользователя страница 26

Страница: 26 / 89

GVS K-BUS

○

KNX/EIB

Thermostat

www.video-star.com.cn

[email protected]

Tel.

：

（

8620

）

39338986

Fax.

：（

8620

）

39338465

Parameter “Object type for operating mode switchover”

Options

：

1bit

1byte

This Parameter is use for giving a definition of object type when switching mode room’s temperature

work patterns.

When choosing

“

1bit”

，

you can find the type of

“

Active frost/heating protection mode”,

“

Active night

mode” and

“

Active comfort mode”. These types can switch the room temperature controller into different

work patterns. The work pattern will switch to standby mode when the value of all these three type is

“0”.

Choosing

“

1bit”, the priority of every work patterns are as follows. (

Frost/heating protection

→

Comfort

→

night

→

standby

forcing

switchover

Window

status

Presence

object

1bit switching

Work pattern to be

activated

Comfort

Standby Night Frost/heating

protection

Comfort

Standby

Night

Frost/heating

protection

Frost/heating

protection

Comfort

Standby

Night

Frost/heating

protection

When choosing

“

1byte”, you can find the type of

“

Temperature operating mode switchover”. Under

this circumstances, different Room temperature controller can be switched into different work patterns by

setting every value of type. Values to the work pattern is as follows. 0 - Automation (comfort mode). 1 -

Comfort mode. 2 - Standby mode. 3 - Night mode. 4 - Frost/Heating protecting mode. 5 - Reserved.

Содержание CHTC-86/01.1.21


























































































Результаты поиска

Содержание CHTC-86/01.1.21

Отзывы:

Похожие инструкции для CHTC-86/01.1.21

Бренды по названию

Популярные бренды

GVS CHTC-86/01.1.21, Руководство пользователя

Результаты поиска

Содержание CHTC-86/01.1.21

Отзывы:

Похожие инструкции для CHTC-86/01.1.21

Бренды по названию

Популярные бренды