GVS CHTC-86/01.1.21 Скачать руководство пользователя страница 79

Страница: 79 / 89

GVS K-BUS

○

KNX/EIB

Thermostat

www.video-star.com.cn

[email protected]

Tel.

：

（

8620

）

39338986

Fax.

：（

8620

）

39338465

Bit0: flag of enabling comfort mode 1---enable

0----disable

Bit1: flag of enabling standby mode 1---enable

0----disable

Bit2: flag of enabling night mode 1---enable

0----disable

Bit3: flag of enabling frost / heat protection mode 1---enable

0----disable

Bit4: flag of disable temperature control 1---disable

0----enabled

Bit5: flag of heating/cooling 0—cooling 1—heating.

Bit6: flag of dead zone Select both heating and cooling control functions, and when the current temperature is in the

dead zone, set 1, otherwise set 0.

Bit7: flag of frost alarm When the actual temperature is below 5

℃

, set 1, otherwise set 0. This bit is only as alert

signs, has no effect on the temperature control.

Output RHCC status

Temperature

control

2 byte

C, R, T

22.101 DPT_StatusRHCC

RHCC Status Report

Bit no: 0: error

，

“1” alarm

，

“0” normal

8: heating or cooling, "0" cooling, "1" heating

12: Dewpoint alarm, "1" alarm, "0": normal

13: frost alarm, "1" alarm, "0": normal

14: over-heat/cold alarm "1" alarm, "0": normal

Over-heat: the current temperature exceed 35

℃

, Over-cooling: the current temperature below 15

℃

19/20

/24/2

Basic/ heating/cooling control

value

Additional heating/cooling

control value

Temperature

control

1bit

1byte

C, R, T

1.001 DPT_Switch

5.001 DPT_Scaling

This communication object is used to send the control value of heating /cooling, to control actuator ON/OFF, and

adjust the room temperature.

Send telegrams

（

two position control――1bit

）：

on/off

Send telegrams

（

two position control ――1byte

）

：

0%/100%

Send telegrams

（

continuous PI control

）

：

0…100%

Send telegrams

（

switching PI control

）

：

on/off

Send telegrams

（

switching PI control

）

：

on/off

Содержание CHTC-86/01.1.21


























































































Результаты поиска

Содержание CHTC-86/01.1.21

Отзывы:

Похожие инструкции для CHTC-86/01.1.21

Бренды по названию

Популярные бренды

GVS CHTC-86/01.1.21, Руководство пользователя

Результаты поиска

Содержание CHTC-86/01.1.21

Отзывы:

Похожие инструкции для CHTC-86/01.1.21

Бренды по названию

Популярные бренды