GVS CHTC-86/01.1.21 Скачать руководство пользователя страница 48

Страница: 48 / 89

GVS K-BUS

○

KNX/EIB

Thermostat

www.video-star.com.cn

[email protected]

Tel.

：

（

8620

）

39338986

Fax.

：（

8620

）

39338465

"1bit/1byte output, temperature", when the detected temperature is below the low threshold or above the

high threshold.

If select "do not send telegram", no telegram is sent; if select "send following telegram once", the

telegram is sent once; if select "send cyclically", the telegram is sent cyclically; send cyclically time can

be set in the below "cycle time for temperature threshold value [min]", and at most two values can be set,

in the below logic1bit/ 1byte telegram value.

Parameter "logic 1 bit /1byte telegram value"

Options: Logic 1bit (0~1)

1byte

（

0~255

）

This parameter is used to specify, the telegram value that object "1bit/1byte output, temperature"

sends, when the current temperature is below the low threshold and above the high threshold. After a

bus reset or programming, if the current temperature is between the low threshold and the high threshold,

the object does not send telegram to the bus.

Parameter "Cycle time for temperature threshold value [min](if used)"

Options: 1- 255

This parameter is used to set the object "1bit/1byte output, temperature" cycle time on the bus to

send the value of the interval, only when the parameter "If temperature is lower / upper than threshold

value" set loop send it to use.

Parameter "use block of the temperature threshold output"

Options: yes

This parameter sets whether to enable the threshold value, if enabled, the object "temperature

threshold value1 / 2 block" is visible, when the object receives telegram "1", threshold value is disabled,

when the object receives telegram "0", the threshold value is enabled.

Parameter "Behaviour when setting the lock"

Options: Do not send telegram

Send the same telegram as lower threshold

Содержание CHTC-86/01.1.21


























































































Результаты поиска

Содержание CHTC-86/01.1.21

Отзывы:

Похожие инструкции для CHTC-86/01.1.21

Бренды по названию

Популярные бренды

GVS CHTC-86/01.1.21, Руководство пользователя

Результаты поиска

Содержание CHTC-86/01.1.21

Отзывы:

Похожие инструкции для CHTC-86/01.1.21

Бренды по названию

Популярные бренды