GVS CHTC-86/01.1.21 Скачать руководство пользователя страница 45

Страница: 45 / 89

GVS K-BUS

○

KNX/EIB

Thermostat

www.video-star.com.cn

[email protected]

Tel.

：

（

8620

）

39338986

Fax.

：（

8620

）

39338465

"Threshold value in% for fan speed 3 at heating”: to set packet value that "communication object

22-Fan manual stage" outputs when the Thermostat is switched to high speed 3.

Parameter "Fan speed for switching to comfort mode"

Parameter "Fan speed for switching to standby mode"

Parameter "Fan speed for switching to night mode"

Parameter "Fan speed for switching to frost/heat protection mode"

Options: auto

no change

This parameter is to set wind-sharing speed of fain coil in different operating modes. Each mode

can be set its corresponding wind speed. When switching to a working mode, the communication object

sends the control value, the corresponding wind speed.is entered.

Each switching to an operation

mode, timing mark start timing in "speed return mode", time will return to automatic speed mode.

4.9 Parameter window "Threshold value"

Parameter window "Threshold value" is shown in Figure 4.9: here is to set the threshold values of of

temperature and humidity, which can be enabled in the interface. When the temperature threshold value

is enabled, the parameter window is shown in Figure 4.9.1; when the humidity threshold value when

enabled, the parameter window is shown in Figure 4.9.2. Thermostat, according to the current

temperature and humidity within the threshold value range, triggers to send two different types of

(1bit/1byte) data to the BUS, to control other devices.

Содержание CHTC-86/01.1.21


























































































Результаты поиска

Содержание CHTC-86/01.1.21

Отзывы:

Похожие инструкции для CHTC-86/01.1.21

Бренды по названию

Популярные бренды

GVS CHTC-86/01.1.21, Руководство пользователя

Результаты поиска

Содержание CHTC-86/01.1.21

Отзывы:

Похожие инструкции для CHTC-86/01.1.21

Бренды по названию

Популярные бренды