GVS CHTC-86/01.1.21 Скачать руководство пользователя страница 38

Страница: 38 / 89

GVS K-BUS

○

KNX/EIB

Thermostat

www.video-star.com.cn

[email protected]

Tel.

：

（

8620

）

39338986

Fax.

：（

8620

）

39338465

Parameter “control parameter of cooling system”

Options

：

Cooling ceiling (5K/240min)

Split unit (4K/90min)

PI auto tuning

User-defined parameter

If the option is "PI auto tuning", you can obtain the PI parameters through auto tuning. After

programming the Thermostat starts auto-tuning, makes room temperature oscillate upper and lower

around temperature setpoint through fully open and fully close operations. After two oscillation cycles, PI

parameters will be calculated according to the amplitude and period of oscillation waveform. Finally, the

the self-tuning state ends and turns to PI control state, which controls according to the parameters got

from auto tuning. When the bus turns off and then turns on PI continues to control according to those

parameters. The period of Self-tuning ranges from tens of minutes to several hours depending on the

controlled object. Parameters got from PI auto tuning may not be optimal.During the process of PI auto

tuning, please do not adjust temperature setpoint, or convert heating and refrigeration to prevent

interference of PI auto tuning.

In the option of "user-defined parameter", PI parameter values can be set through the following two

parameters and application of Thermostat will calculate the control value basing on the given parameter

values.

PI parameter values of other options are specified.

Parameter "proportional range (× 0.1

℃

Options: 10 ... 100

In the parameter "control parameter of heating / cooling system",when the option is "user-defined

parameter", this parameter is visible and is used to set parameter values of P (proportional band) with

the unit is

℃

. Proportional factor equals to 255 divided by ratio range. The proper ratio range must be

appropriately set. If it is too small it will cause very fast adjustment and overshoot.If it is too large it will

cause very slow adjustment,but not overshoot. For example: the ratio range is 5

℃

, when temperature

deviation is 2

℃

,proportional control value will be(255/5) * 2 = 102. PI control value equals proportional

control value plus integral term control value.

Parameters "reset time (min)"

Содержание CHTC-86/01.1.21


























































































Результаты поиска

Содержание CHTC-86/01.1.21

Отзывы:

Похожие инструкции для CHTC-86/01.1.21

Бренды по названию

Популярные бренды

GVS CHTC-86/01.1.21, Руководство пользователя

Результаты поиска

Содержание CHTC-86/01.1.21

Отзывы:

Похожие инструкции для CHTC-86/01.1.21

Бренды по названию

Популярные бренды