GVS CHTC-86/01.1.21 Скачать руководство пользователя страница 76

Страница: 76 / 89

GVS K-BUS

○

KNX/EIB

Thermostat

www.video-star.com.cn

[email protected]

Tel.

：

（

8620

）

39338986

Fax.

：（

8620

）

39338465

by multiple sensors, or temperature by external sensor.

rel. humidity

Humidity

2 byte

C, R, T

9.007 DPT_Value_Humidity

The communication object is used to send the current humidity that is detected by the thermostat panel sensor, to the

bus; the transmission time is set via parameter settings.

Operating mode forced object

Setpoint

temperature

1 byte

C,R,W

20.102 DPT_HVACMode

This communication object is mandatory conversion of operating mode, and has the highest priority. Different

telegrams mean different operating modes, as follows: 0: Auto (comfortable), 1: comfort mode, 2: Standby mode, 3: Night

Mode, 4: Frozen protection /heat protection, 5~255: Reserved, do not use. For example, when an object receives a

telegram "2", the thermostat panel will control the actuator according to the standby mode setting.

Window status

Setpoint

temperature

1 bit

C, R, W

1.019 DPT_Window_Door

This communication object is used to connect a window contact

Receive telegram "1" - the windows open

Receive telegram "0" - the windows closed

Presence object:

Setpoint

temperature

1 bit

C, R,W

1.001 DPT_Switch

This communication object is used to connect presence sensor

Receive telegram "1" - somebody or something exists

Receive telegram "0" - somebody or something doesn't exist

Active comfort mode

Setpoint

temperature

1 bit

C, R,W

1.001 DPT_Switch

The communication object is visible when the object type of operating mode is "1bit", and is used to activate comfort

mode. Receiving telegram "1"will activate comfort mode; receiving telegram "0" will not activate comfort mode.

Receive telegram "1"----activate comfort mode

Receive telegram "0"----not activate comfort mode

Active standby mode

Setpoint

temperature

1 bit

C, R,W

1.001 DPT_Switch

Содержание CHTC-86/01.1.21


























































































Результаты поиска

Содержание CHTC-86/01.1.21

Отзывы:

Похожие инструкции для CHTC-86/01.1.21

Бренды по названию

Популярные бренды

GVS CHTC-86/01.1.21, Руководство пользователя

Результаты поиска

Содержание CHTC-86/01.1.21

Отзывы:

Похожие инструкции для CHTC-86/01.1.21

Бренды по названию

Популярные бренды