GVS CHTC-86/01.1.21 Скачать руководство пользователя страница 23

Страница: 23 / 89

GVS K-BUS

○

KNX/EIB

Thermostat

www.video-star.com.cn

[email protected]

Tel.

：

（

8620

）

39338986

Fax.

：（

8620

）

39338465

This parameter setting defines the transmission time interval of the thermostat panel cycle send to

other devices in the bus through its communication objects “rel. humidity.

4.4 Parameter setting interface“Heating/Cooling setpoint”

In the setting of “Temperature control system”, parameter’s setting content will be different in this

page according to your choice from “Cooling”, ”Heating” or “Heating and Cooling”. Temperature can be

set here under any work patterns, including relative mode and absolute mode.

Figure 4.4.1 Parameter setting interface of “Heating setpoint”

Содержание CHTC-86/01.1.21


























































































Результаты поиска

Содержание CHTC-86/01.1.21

Отзывы:

Похожие инструкции для CHTC-86/01.1.21

Бренды по названию

Популярные бренды

GVS CHTC-86/01.1.21, Руководство пользователя

Результаты поиска

Содержание CHTC-86/01.1.21

Отзывы:

Похожие инструкции для CHTC-86/01.1.21

Бренды по названию

Популярные бренды