GVS CHTC-86/01.1.21 Скачать руководство пользователя страница 15

Страница: 15 / 89

GVS K-BUS

○

KNX/EIB

Thermostat

www.video-star.com.cn

[email protected]

Tel.

：

（

8620

）

39338986

Fax.

：（

8620

）

39338465

This parameter is the communication object sending period for testing whether Thermostat is

normal or not, and mainly being sent to the bus circularly to tell whether Thermostat is normal or not

through object "in operation”.

Parameter “Temperature display”

Options

：

Celsius (C)

Fahrenheit (F)

Here setting the LCD panel temperature display unit. Choose “Celsius (C)”the temperature will be

displayed in Celsius; Choose "Fahrenheit (F)" the temperature will be displayed in Fahrenheit.

Parameter “Backlight in no operation in day (%)”

Parameter “Backlight in operation in day (%)”

Parameter “Backlight in no operation in night (%)”

Parameter “Backlight in operation in night (%)”

Options

：

0…100%

This parameter is mainly used to set up the LCD panel backlight brightness.in the daytime or at

night under the condition of operation and non-operation .The user can set the day or night through the

bus, also can identify the day or night by time points .

Parameter “Time of backlight delay(s)”

Options

：

5…50 s

This parameter is mainly used for setting the backlight value from operating status to non-operation

status. Namely when nobody operates screen, delaying the parameter time, entering the screen

backlight without operation.

Parameter “Switch day/night mode automatically"

Options: no

yes

Set the mode automatically switches about whether to activate the day / night backlight brightness.

Содержание CHTC-86/01.1.21


























































































Результаты поиска

Содержание CHTC-86/01.1.21

Отзывы:

Похожие инструкции для CHTC-86/01.1.21

Бренды по названию

Популярные бренды

GVS CHTC-86/01.1.21, Руководство пользователя

Результаты поиска

Содержание CHTC-86/01.1.21

Отзывы:

Похожие инструкции для CHTC-86/01.1.21

Бренды по названию

Популярные бренды