GVS CHTC-86/01.1.21 Скачать руководство пользователя страница 50

Страница: 50 / 89

GVS K-BUS

○

KNX/EIB

Thermostat

www.video-star.com.cn

[email protected]

Tel.

：

（

8620

）

39338986

Fax.

：（

8620

）

39338465

4.9.2 Humidity threshold value

Figure 4.9.2 Parameter window "Humidity threshold value 1/2"

Parameter "Humidity threshold value (%)"

Options: 0- 100

This parameter sets a high threshold value humidity, this threshold value can be changed as

"change humidity threshold value1 / 2", and once changing, in the bus will save the new value when the

power of the BUS is off.

Parameter "Negative hysteresis humidity (%)"

Options: 1-10

This parameter is used to set the hysteresis value of the low threshold value to high threshold value.

Assuming the hysteresis value is 5%, then the lower threshold = high threshold value -5%. When

the high threshold changes, the low threshold changes accordingly.

Parameter "If humidity is lower than threshold value"

Parameter "If humidity is upper than threshold value"

Options: Do not send telegram

Send following telegram once

Содержание CHTC-86/01.1.21


























































































Результаты поиска

Содержание CHTC-86/01.1.21

Отзывы:

Похожие инструкции для CHTC-86/01.1.21

Бренды по названию

Популярные бренды

GVS CHTC-86/01.1.21, Руководство пользователя

Результаты поиска

Содержание CHTC-86/01.1.21

Отзывы:

Похожие инструкции для CHTC-86/01.1.21

Бренды по названию

Популярные бренды