GVS CHTC-86/01.1.21 Скачать руководство пользователя страница 86

Страница: 86 / 89

GVS K-BUS

○

KNX/EIB

Thermostat

www.video-star.com.cn

[email protected]

Tel.

：

（

8620

）

39338986

Fax.

：（

8620

）

39338465

When CH A "Switch" is enabled, this communication object is visible, through long push, according to the parameters

settings, performs the corresponding actions, e.g. ON, OFF, TOGGLE, etc. When the telegram is "1"--- ON; When the

telegram is "0"--- OFF.

55/58/61

Disable input 1/2/3

CH A Disable

1bit

C,W

1.001 DPT_Switch

When the channel function is enabled, the communication object is activated, which is used to disable / enable

channel function. When this communication object receives a logic value of "0", the channel function is enabled; receives

"1", disabled. When the channel function is disabled, control telegrams sent by all objects are invalid. When the bus power

is restored, channel function is enabled by default. (If all communications objects with channel function are "Disable", the

operations performed are the same)

5.6.2

"Dimming" Communication Object

5.6.2 "Dimming" Communication Object

Number

Communication object name

Functions

Data Types

Flags

DPT

53/56/59

Switch

CH A Switch

1bit

C, W,T

1.001 DPT_Switch

When CH A "Switch" is enabled, this communication object is visible, through short push, according to the parameters settings,

performs the

corresponding

actions, e.g. ON, OFF, TOGGLE, etc. When the telegram is "1"--- ON; When the telegram is "0"---

OFF.

54/57/60

Switch 2, input 1/2/3

CH A Switch-long

4bit

C, T

3.007 DPT_Control_Dimming

The communication object via contact input, send brighten or darken command, User can control the dimming device on the bus,

conduct relative dimming. When the input is disconnected, it will send an end command to stop dimming.

55/58/61

Disable input 1/2/3

CH A Disable

1bit

C,W

1.001 DPT_Switch

As above.

5.6.3

"Shutter" Communication Object

Figure 5.6.3 “shutter” communication object

Number

Object name

Functions

Data Types

Flags

DPT

Содержание CHTC-86/01.1.21


























































































Результаты поиска

Содержание CHTC-86/01.1.21

Отзывы:

Похожие инструкции для CHTC-86/01.1.21

Бренды по названию

Популярные бренды

GVS CHTC-86/01.1.21, Руководство пользователя

Результаты поиска

Содержание CHTC-86/01.1.21

Отзывы:

Похожие инструкции для CHTC-86/01.1.21

Бренды по названию

Популярные бренды