Gree VERSATI III Series Скачать руководство пользователя

Страница: 55 / 135

Unit Control

[Notes]



At the commissioning parameter setting page, when the state of any function changes, the system

will automatically save this change and this change will remain upon power failure.



Do not modify any commissioning parameter except the approved qualified servicemen, as it

would give birth to adverse effects to the unit.

Commissioning Function Setting

Item

Range

Default

Description

Ctrl. state

T-water out/T-room

T-water out

When ―

Remote sensor

‖ is set to ―

With

‖, it

can be set to ―

T-room

‖.

2-Way valve

Cool 2-Way valve, On/Off

Off

It will decide the status of the 2-way valve

under the ―

Cool

‖ and ―

Cool + Hot water

‖

modes.

Heat 2-Way valve, On/Off

It will decide the status of the 2-way valve

under the ―

Heat

‖ and ―

Heat + Hot water

‖

modes

Solar setting

With/Without

Without

1. When the water tank is unavailable,

this setting will be reserved.

When it is set to ―

With

‖, the solar kitting

will work on its own.

When it is set to ―

Without

‖, hot water

by the solar kitting is unavailable.

Water tank

With/Without

Without

Thermostat

Without/Air/Air+ hot water

Without

1. This setting cannot be interchanged

between ―

Air

‖ and ―

Air+ hot water

‖

directly but via ―

Without

‖ this option

Each time when ―

Air

‖ or ―

Air + hot

water

‖ is switched to ―Without‖, the unit

will go to the OFF status. Meanwhile,

the control will send out ―

OFF

‖

command for consecutive 40 seconds

(it is longer than the communication

error, and the ―

‖ command can be

performed only when 40 seconds have

been expired.

Содержание VERSATI III Series








































































































































Результаты поиска

Содержание VERSATI III Series

Отзывы:

Похожие инструкции для VERSATI III Series

Бренды по названию

Популярные бренды

Gree VERSATI III Series, Руководство по обслуживанию

Результаты поиска

Содержание VERSATI III Series

Отзывы:

Похожие инструкции для VERSATI III Series

Бренды по названию

Популярные бренды