Gree VERSATI III Series Скачать руководство пользователя страница 132

Страница: 132 / 135

Test Operation & Troubleshooting & Maintenance

Plate Heat

Exchanger

It is the water-refrigerant plate type heat exchanger, used to

liquefy the high-temperature high-pressure vapor refrigerant or

evaporate the low-temperature low pressure liquid refrigerant.

Heat of condensation is taken away by circulation water and

heat for evaporation is supplied also by circulation water.

Water Pump

It is the power equipment for water circulation.

Expansion Tank

It is used to keep stable pressure of the water system. The tank

is charged with a certain volume of nitrogen which is separated

from the water side with a gasbag. When pressure of the water

side exceeds the nitrogen pressure, the gasbag will expand and

water enters into the tank so as to lower the pressure of the

water system. In contract, when pressure of the water system

goes down, nitrogen in the tank will expel water out to the water

system.

Flow Switch

It is used to prevent the heat exchanger from being frozen

owing to reduced water flow rate. When the flow rate goes down

to the point at which the flow switch will act, the switch will trip

off and the unit will raise an alarm and shut down.

Economizer

It is used in heating mode and water heating mode but NOT

used in cooling mode.On one side,it can increase the

subcooling before EXV,and on the other side it can enchance

the refrigerant in heating circuit.

Содержание VERSATI III Series








































































































































Результаты поиска

Содержание VERSATI III Series

Отзывы:

Бренды по названию

Популярные бренды

Gree VERSATI III Series, Руководство по обслуживанию

Результаты поиска

Содержание VERSATI III Series

Отзывы:

Бренды по названию

Популярные бренды