Gree VERSATI III Series страница 133 Скачать руководство пользователя

Страница: 133 / 135

Test Operation & Troubleshooting & Maintenance

Safety Valve

It is used to prevent the pressure of circulation water from

increasing unusually. When the pressure is larger than the set

point (0.6MPa), this valve will open to relieve water pressure.

Exhaust Valve

It is used to expel air trapped inside the water system to make

sure normal operation of the system. It is usually installed at the

highest point of the system.

5.3.2 Charging and Discharging of Refrigerant

The unit has been charged with refrigerant before delivery. Overcharging or undercharging will cause

the compressor to run improperly or be damaged. When refrigerant is required to be charged or

discharged for installation, maintenance and other reasons, please follow steps below and nominal

charged volume on the nameplate.

Discharging: remove metal sheets of the outer casing, connect a hose to the charging valve and then

discharge refrigerant:

Note:

(a) Discharge is allowed unless the unit has been stopped. (Cut off the power and repower it 1

minutes later)

(b) Protective measures should be taken during discharging to avoid frost bites.

avoid air or foreign matters entering the unit.

(d) Vacuuming: when discharging is finished, use hoses to connect the charging valve, manometer

and vacuum pump to vacuum the unit.

Содержание VERSATI III Series








































































































































Результаты поиска

Содержание VERSATI III Series

Отзывы:

Похожие инструкции для VERSATI III Series

Бренды по названию

Популярные бренды

Gree VERSATI III Series, Руководство по обслуживанию

Результаты поиска

Содержание VERSATI III Series

Отзывы:

Похожие инструкции для VERSATI III Series

Бренды по названию

Популярные бренды