Gree VERSATI III Series Скачать руководство пользователя страница 68

Страница: 68 / 135

Unit Control

board

AC contactor protection or input over-zero error AC contactor

Temperature drift protection

Temp. drift

Sensor connection protection ( the current

sensor fails to be connected with the

corresponding phase U and or phase V)

Sensor con.

Communication error between the display

panel and the outdoor unit

ODU Com.

Refrigerant vapor line temperature sensor error Temp RGL

Refrigerant liquid line temperature sensor error

Temp RLL

3.2.5.4 Error Log

[Operation Instructions]

★

At the ―

VIEW

‖ page, by touching ―

Error log

‖, the control panel will go to the error log page, where it is

able to view error records.

[Notes]:
● The error log can accommodate up to 20 pieces of error. Name and occurrence time are available for
each error.
● When error log exceeds 20, the latest will supersede the earliest.

3.2.5.5 Version Viewing

[Operation Instructions]

★

At the ―

VIEW

‖ page, by touching ―

Version

‖, the control panel will go to the version view page, where

it is able to view both the program version and protocol version.

Содержание VERSATI III Series








































































































































Результаты поиска

Содержание VERSATI III Series

Отзывы:

Бренды по названию

Популярные бренды

Gree VERSATI III Series, Руководство по обслуживанию

Результаты поиска

Содержание VERSATI III Series

Отзывы:

Бренды по названию

Популярные бренды