Gree VERSATI III Series Скачать руководство пользователя страница 98

Страница: 98 / 135

Installation

Net weight

Gross weight

Joints Dimension

Description

Joint pipe thread

Hot water outlet of water tank

1/2″Female BSP

Circulating water inlet/outlet of water tank

3/4″Female BSP

Cooling water inlet of water tank

1/2″Female BSP

Pipe joint

3/4″Female BSP

4.7.3 Connection of waterway system

(1) If connection between water tank and indoor unit should be through the wall, drill a hole φ70 for

pass of circulating water pipe. It is unnecessary if the hole is not needed.

(2) Preparation of pipelines: Circulating water outlet/inlet pipe must be hot water pipe, PPR pipe with

nominal out diameter of dn25 and S2.5 series (wall thickness of 4.2mm) being recommended. Cooling

water inlet pipe and hot water outlet pipe of water tank should also be hot water pipe, PPR pipe with

nominal out diameter of dn20 and S2.5 series (wall thickness of 3.4mm) being recommended. If other

insulated pipes are adopted, refer to the above dimensions for out diameter and wall thickness.

(3) Installation of circulating water inlet/outlet pipes: connect the water inlet of the unit with circulating

outlet of water tank and water outlet of unit with circulating inlet of water tank.

(4) Installation of water inlet/outlet pipes of the water tank: safety check valve, filter and cut-off valve

must be installed for the water inlet pipe according to the installation sketch of the unit. At least a cut-off

valve is needed for the water outlet pipe.

(5) Installation of blow-off pipes at the bottom of water tank: connect a piece of PPR pipe with

drainage outlet to floor drain. A cut-off valve must be installed in the middle of the drainage pipe and at

the place where it is easy to be operated by the users.

(6) After connection of all waterway pipelines, perform the leakage test firstly. After that, bind up the

water pipes, water temp sensor and wires with wrapping tapes attached with the unit.

(7) Refer to Installation Sketch of the Unit for details.

Description

Joint pipe thread

Circulating water inlet/outlet of main unit

1″Male BSP

Cooling water inlet of water tank

1/2″Female BSP

Circulating water inlet/outlet of water tank

3/4″Female BSP

Hot water outlet of water tank

1/2″Female BSP

Содержание VERSATI III Series








































































































































Результаты поиска

Содержание VERSATI III Series

Отзывы:

Бренды по названию

Популярные бренды

Gree VERSATI III Series, Руководство по обслуживанию

Результаты поиска

Содержание VERSATI III Series

Отзывы:

Бренды по названию

Популярные бренды