Gree VERSATI III Series страница 47 Скачать руководство пользователя | Manualshive

Страница: 47 / 135

background image

Unit Control

●When it is set to ―

On

‖, it will automatically back to ―

Off

‖ when the main unit is turned off; while it is set to

―

Timer

‖, this setting will remain when the main unit is turned off and can only be canceled manually.

●It will be memorized upon power failure.

3.2.2.6 Weather Depend

[Operation Instructions]

★

At the function setting page, by touching ―

Weather depend

‖, there will be a choice box, where it is

able to set it to ―

On

‖ or ―

Off

‖, and also it is able to set the weather-dependent temperature.

Page of the Weather Depend

[Notes]
●When ―

Weather depend

‖ has been activated; it cannot be deactivated by ON/OFF operation but

done manually.
●It is available to find the weather-dependent target temperature at that parameter viewing pages.
●When this function has been activated, it is still allowed to set the room temperature, however, this
setting becomes valid only when ―

Weather depend

‖ has been deactivated.

●This function can be set to ―

On

‖ no matter the unit is turned on or off, but works only when the unit is

turned on.
●This function only works for air conditioning. Under the ―

Hot water

‖ mode, it cannot be activated.

●It will be memorized upon power failure.

3.2.2.7 Weekly Timer

[Operation Instructions]

★

1. At the function setting page, by touching ―

Weekly timer

‖, it will go to the setting page as shown

below.

★

2. At the ―

Weekly timer

‖ setting page, as shown in the figure below, the weekly timer can be set to ―

On

‖

or ―

Off

‖.

★

3. At the ―

Weekly timer

‖ setting page, by touching the desired day (Monday ~ Sunday) it will access to

«
...
45
46
47
48
49
...
»

Содержание VERSATI III Series








































































































































Отзывы:

Нет отзывов

Похожие инструкции для VERSATI III Series

Бренд: Panasonic Страницы: 56

Бренд: Panasonic Страницы: 60

Бренд: Panasonic Страницы: 297

Бренд: Danby Страницы: 36

Бренд: Daewoo Страницы: 131

Бренд: REMKO Страницы: 56

Бренд: Levoit Страницы: 12

Бренд: EINHELL Страницы: 52

Бренд: AllerAir Страницы: 1

GSC 18 FV 5 HRML

Бренд: Godrej Страницы: 24

DYNAPACK S Series

Бренд: Suburban Страницы: 22

Бренд: Kelvinator Страницы: 12

Classic Plus 15

Бренд: Dawlance Страницы: 13

Бренд: Technibel Страницы: 45

MinusA2 SPA-780N

Бренд: Rabbit Air Страницы: 2

Бренд: Saivod Страницы: 88

50PG08 14 Series

Бренд: Carrier Страницы: 20

NTC5/GNJ Series

Бренд: ICP Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды