Gree VERSATI III Series страница 53 Скачать руководство пользователя

Страница: 53 / 135

Unit Control

[Notes]

：

● It can be performed only when the unit is turned off.

3.2.2.16 WiFi Reset

[Operation Instructions]

★

At the function setting page, by touching ―

WiFi

‖, a choice box will pop up, where by touching ―

‖ , the

WiFi setting will be reset, and by touching ―

Cancel

‖ the choice box will quit and WiFi will not be reset.

3.2.2.17 Reset

[Operation Instructions]

★

At t

he function setting page, by touching ―

Reset

‖, a choice box will pop up, where by touching ―

‖ all

user parameter settings will be reset and by touching ―

Cancel

‖ it will back to the function setting page.

[Notes]

：

● This function is allowed only when the unit has turned off.
● This function is valid for ―

Temp. timer

‖, ―

Clock timer

‖, ―

Preset mode

‖, ―

Weekly timer

‖, and ―

Weather

depend

‖.

3.2.3 User Parameter Setting

[Operation Instructions]

★

1. At the menu page, by touching ―

PARAMETER

‖, it will back to the parameter setting page, as shown

in the figure below.

Parameter Setting Page

★

2. At the menu setting page, by touching the page turning keys, it is able to switch to the page where

the desired parameter is.

★

3. After that, this setting will be saved by tou

ching ―

‖ and then the unit will run based on this setting.

While this setting will give up by touching ―

Cancel

‖.

[Notes]

：

●

For parameters with different defaults under different conditions, when conditions changes, the

Содержание VERSATI III Series








































































































































Результаты поиска

Содержание VERSATI III Series

Отзывы:

Похожие инструкции для VERSATI III Series

Бренды по названию

Популярные бренды

Gree VERSATI III Series, Руководство по обслуживанию

Результаты поиска

Содержание VERSATI III Series

Отзывы:

Похожие инструкции для VERSATI III Series

Бренды по названию

Популярные бренды