Gree VERSATI III Series страница 62 Скачать руководство пользователя | Manualshive

Страница: 62 / 135

background image

Unit Control

3.2.4.13 Gate-Ctrl.

[Operation Instructions]

★

At the commissioning parameter setting page, by touching ―

Gate-Ctrl.

‖, the control panel will access

to the corresponding setting page.

[Notes]
●When ―

Gate-Ctrl.

‖ has been activated; the display panel will detect the card state. When the card has

inserted, the unit will run normally. When the card is drawn out, the controller will turn off the unit at

once and back to the homepage. In this case, all touching operation become ineffective, and a prompt

dialog box will pop up. The unit will resume normal operation until the card has inserted back and the

ON/OFF status of the control panel will resume to that before the card is drawn out.
●This setting will be memorized upon power failure.

3.2.4.14 Current Limit

[Operation Instructions]

★

1. At the commissioning parameter setting page, by touching ―

Current limit

‖, it can be set to ―

On

‖ or

―

Off

‖.

★

2. When it is set to ―

On

‖, it is able to set the limited current value.

★

3. After that, this setting will be saved by touching the ―

Save

‖ icon,

[Notes]
● This setting will be memorized upon power failure.

3.2.4.15 Address

[Operation Instructions]

★

At the commissioning parameter setting page, by tou

ching ―

Current limit

‖, it can be set the address.

[Notes]

：

● It is used to set the address of the control panel for being integrated to the centralized control system.
● This setting will be memorized upon power failure.
● The setting range is 1~125 and 127~253.
● The defaulted address is 1 upon first power-on.

3.2.4.16 Refrigerant Recovery

[Operation Instructions]

★

At the commissioning parameter setting page, by touching ―

Refri. recovery

‖, it will access to the

refrigerant recovery page.

★

When ―

Refri. recovery

‖ is set to ―

On

‖, the control panel will go back to the home page. At this time,

any touch operation except ON/OFF will get no response, with a prompt dialog box popping up,
saying ―

The refrigerant recovery is running!

‖ By touching ON/OFF, refrigerant recovery will quit.

«
...
60
61
62
63
64
...
»

Содержание VERSATI III Series








































































































































Отзывы:

Нет отзывов

Похожие инструкции для VERSATI III Series

Бренд: Zephyr Страницы: 6

Бренд: Rasonic Страницы: 2

Бренд: WAGNER Страницы: 5

Бренд: Kogan Страницы: 17

Бренд: Yamato Страницы: 68

Бренд: Cellartec Страницы: 35

Бренд: Sinclair Страницы: 38

Depuro Plus 230

Бренд: Vortice Страницы: 72

Бренд: TCL Страницы: 12

Бренд: Carrier Страницы: 8

Intelli-Pro 3 XJ-3100A

Бренд: Surround Air Страницы: 8

Бренд: Perfect Aire Страницы: 20

Бренд: Sonnenkonig Страницы: 64

Climma Fancoil EVA Series

Бренд: Veco Страницы: 21

Бренд: ICP Страницы: 14

Bycool DINAMIC 1.1

Бренд: dirna Bergstrom Страницы: 36

Бренд: Fuji Electric Страницы: 22

Бренд: Garrison Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды