Gerber ODYSSEY XP Скачать руководство пользователя страница 77

Страница: 77 / 84

Chapter 8:
HPGL Support

This chapter contains information on Hewlett-Packard Graphics
Language (HPGL) commands supported by the ODYSSEY XP plotter.
These supported commands are used by selected third-party software
vendors to operate the ODYSSEY XP plotter.

For specific information on third-party software, contact the vendor of
that software.

This chapter also includes information about:

♦

HPGL test file

♦

changing HPGL units

HPGL command set

The following HPGL commands are recognized by the ODYSSEY XP
plotter.

- Set HPGL defaults

- Initialize tool settings

- Output current x,y position of the tool in plotter units.

- Output Error (first error)

Valid respond

Condition

Unknown error

Unknown command

Wrong number of parameters for command

Parameter out of range

Parameter value overflow

Data buffer overflow

- Output Hardware travel limits (X

min

max

). Responds with

four numbers (0.005mm per unit) separated by commas. For example:
0,0,9144000,138430

- Output Identification string

Содержание ODYSSEY XP





















































































Результаты поиска

Содержание ODYSSEY XP

Отзывы:

Бренды по названию

Популярные бренды

Gerber ODYSSEY XP, Руководство пользователя

Результаты поиска

Содержание ODYSSEY XP

Отзывы:

Бренды по названию

Популярные бренды