manualshive.com logo in svg

Gerber ODYSSEY XP, Руководство пользователя

Поделиться
Скачать
Gerber ODYSSEY XP Скачать руководство пользователя страница 2

COPYRIGHT

COPYRIGHT

 2002 Gerber Scientific Products, Inc. All Rights Reserved.

This document may not be reproduced by any means, in whole or in part, without
written permission of the copyright owner.

This document is furnished to support the 

Gerber

 

ODYSSEY XP

 Plotter. In

consideration of the furnishing of the information contained in this document, the party
to whom it is given assumes its custody and control and agrees to the following:

1.

 

The information herein contained is given in confidence, and any part thereof shall
not be copied or reproduced without written consent of Gerber Scientific Products,
Inc.

2.

 

This document or the contents herein under no circumstances shall be used in the
manufacture or reproduction of the article shown and the delivery of this document
shall not constitute any right or license to do so.

Information in this document is subject to change without notice.

PRINTED IN USA

GSP, GERBER EDGE, and GRAPHIX ADVANTAGE are registered trademarks, and Gerber ODYSSEY XP, GA,
OMEGA, MacImprint, GERBER MAXX, Automatic Material Alignment, and GerberMag, are trademarks of
Gerber Scientific Products, Inc. HPGL is a trademark of Hewlett-Packard Company. Scotchcal is a trademark of 3M
Corporation. Windows is a registered trademark of Microsoft Corporation in the US and other countries.

Содержание ODYSSEY XP





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды