manualshive.com logo in svg

Gerber ODYSSEY XP, Руководство пользователя

Поделиться
Скачать
Gerber ODYSSEY XP Скачать руководство пользователя страница 61

55

 

5

 

The Version number appears. Your Gerber Field Service
representative can interpret it for you.

Note: This display is shown as an example only. The display on your plotter
might be different.

To access the firmware version number during power up

During power up, hold down any key while the copyright message
displays. Press any key to resume the power up sequence.

Warning messages

Several common messages can appear to warn an operator before
possible problems happen.

Copy is not possible

Normally, a job sent to the plotter can be repeated many times. In one of
the following conditions, a job is not stored and copying is not possible.

♦

 

The job was cleared from memory and is no longer present.

♦

 

The job was run, but was never completed.

♦

 

The job exceeded the memory capacity of the plotter memory.

To run the job again, you must re-send it from the computer.

EEPROM memory has errors

Some cells in a memory chip have failed and you might not be able to
save certain settings. Other settings are still saved.

Note: Although a diagnostic test can indicate the chip is working, contact Field
Service to report the problem.

The plotter will operate correctly, except you will have to re-enter a
particular setting(s) each time you power up. For example, force settings
will not store, but setting(s) for corners and material type are OK.

ODYSSEY XP
C.3/D.2/C.0/C
* No Foreign Language
S/N:  C019123456

Содержание ODYSSEY XP





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды