manualshive.com logo in svg

Gerber ODYSSEY XP, Руководство пользователя

Поделиться
Скачать
Gerber ODYSSEY XP Скачать руководство пользователя страница 76

70

CHAPTER 7

Maintenance

AC fuse replacement

WARNING: Turn off the power switch and disconnect the power cord
from the power supply.

The fuse is located in the AC power connector on the rear panel where
the power cord plugs into the unit. When this fuse is blown there is no
power supplied to the plotter, nothing appears in the display area, and
the fan is off.

To replace the AC fuse

 

1

 

Turn off the plotter.

 

2

 

Unscrew and remove the serial cable from the rear panel of the
ODYSSEY XP.

 

3

 

Remove the plotter power cord from the socket.

 

4

 

Find the small tab at the right edge of the fuse carrier just to the left of
the power cord receptacle. Insert a flat-tip screwdriver (or a key, as
shown in the photograph) under the tab and gently pry outward,
loosening the carrier.

 

5

 

Pull out the fuse carrier.

 

6

 

Remove the blown fuse. The fuse rating is marked on the fuse itself. Be
sure to replace a blown fuse with a new fuse of identical size and
rating. Reinsert the carrier the same way it came out and press it
firmly into place.

 

7

 

Reconnect the power cord and serial cable.

 

8

 

Turn on the power at the plotter.

Содержание ODYSSEY XP





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды