manualshive.com logo in svg

Gerber ODYSSEY XP, Руководство пользователя

Поделиться
Скачать
Gerber ODYSSEY XP Скачать руководство пользователя страница 62

56

CHAPTER 6

Troubleshooting

If you turn off the plotter, affected settings return to the default. You will
have to re-enter changes to the affected settings.

Job clipped

If a job extends beyond the X or Y axis boundaries, it is too large for the
plotter and displays a 

Job clipped

 message during the run of the job. If

the job is run anyway, it is truncated at the X and Y limits.

To remove the message and start the job, press any key. If the plotter is
in Multi mode and one of the jobs is too large, the plotter runs
automatically until it comes to the job that is too large. It will display the
message, run the job, then stop. The remaining jobs will not run until
you press F1 (Start

−

Job).

Job will not fit

Either the tool is too close to one edge or the back end of the material to
complete the job without running off the material. Do one of the
following:

♦

 

Press F4 (Autofit). The carriage moves automatically to fit the job.

♦

 

Press a slew key to move the carriage and fit the job.

♦

 

Put in a larger sheet of material.

♦

 

Press F2 (Ignore) to run the job anyway. Only that portion of the job
that fits on the material will actually be plotted. A 

Job Clipped

 message

might also appear.

Narrow material

If the middle pinch wheel is on the left edge of the material, the middle
pinch wheel pressure lever should be in the up position. If this message
appears, the lever is in the wrong position.

♦

 

Flip the position of the lever, which is located behind the middle pinch
wheel.

♦

 

Press any key to retry.

Tool is missing

If a tool is not installed in the tool holder when you start a job, the plotter
displays a 

Tool is Missing

 message. If you start the job anyway, the

message disappears and the job starts.

Содержание ODYSSEY XP





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды