manualshive.com logo in svg

Gerber ODYSSEY XP, Руководство пользователя

Поделиться
Скачать
Gerber ODYSSEY XP Скачать руководство пользователя страница 17

11

 

7

 

Pull the pinch wheel lever toward the front to clamp the material
between the grit and pinch wheels.

 

8

 

The control panel displays the following:

 

9

 

Press either F1 (sheet) or F3 (roll) to select the material type. For
information on using the F1, F2, F3, and F4 function keys, refer to
“Learning the control panel” on page 20.

Note:  After pulldown (See page 43), the Odyssey XP will return the material to
the starting position. Do not rewind the surplus material. Allow it to drape over
the dampener bar which promotes a smooth material feed to the cutting tool.

Verifying the material alignment

After you load the material, run auto alignment. The time to perform this
process varies with the amount of error detected.

To perform the material alignment sequence

 

1

 

When the display shows 

Auto Align Material?

, press F3 (Yes).

 

2

 

The display shows 

Locating Pinch Wheels 

while the carriage locates the

pinch wheels.

 

3

 

The display changes to 

Material Auto Align in Progress

 while the

material is moved back and forth as the edge is aligned.

 

4

 

When the material is properly aligned, the Main Menu appears.

SELECT MATERIAL TYPE

 Sheet

Roll

Press  F1  or  F3

Material path before pulldown

Material path after pulldown

Dampener bar

Содержание ODYSSEY XP





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды