manualshive.com logo in svg

Gerber ODYSSEY XP, Руководство пользователя

Поделиться
Скачать
Gerber ODYSSEY XP Скачать руководство пользователя страница 30

24

CHAPTER 3

Running Jobs

After completing the job, the Job Status returns to 

No Job

. If you have

sent several jobs, the Job Status displays 

Ready 

and you will need to

press F1, Start-Job, to plot each job.

Running multiple jobs

Multi mode lets you run several jobs without having to press Start-Job
before each one. When one job finishes, the next job begins immediately.
When all jobs in memory are completed, the plotter waits for another job
and begins as soon as it is received. Multi mode is best used for jobs that
require the same material.

Tip: Make sure you set you set the Start/End Position in the GAPlot32/
GSPPlot program to the end of the job so that the next job doesn’t cut over
the previous one.

To run multiple jobs

 

1

 

Press F2 to toggle between Single and Multi mode. Choose Multi.

 

2

 

Load the material in the plotter.

 

3

 

Install a tool in the tool holder.

 

4

 

Use the slew keys to place the tool where you want the job to begin.

Tip: If the plotter is in a remote location and not near the computer, you can
press F1 (Start Job) on the plotter before you send the jobs from the
computer. The first job will start immediately after it is received.

 

5

 

Send the jobs from your computer to the plotter. When jobs are in
plotter memory, Job Status changes from 

No Job 

to 

Ready

,

 

and 

Start-Job

blinks.

 

6

 

Press F1, Start-Job, to begin the first job. Later jobs will not require
pressing Start-Job again.

F2

MAIN MENU

Start-Job

Settings

Mode: Multi

Menu 1

Job Status:

Ready

F1

MAIN MENU

Start-Job

Settings

Mode: Multi

Menu 1

Job Status:

Ready

Содержание ODYSSEY XP





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды