manualshive.com logo in svg

Gerber ODYSSEY XP, Руководство пользователя

Поделиться
Скачать
Gerber ODYSSEY XP Скачать руководство пользователя страница 72

66

CHAPTER 7

Maintenance

Carriage

To clean the carriage

 

1

 

Remove any tool installed in the tool head

 

2

 

With canned air, gently blow clean the carriage to remove paper dust.

Edge sensors

Use the Clean? menu function to determine if sensors need to be cleaned.

To determine if the sensors need to be cleaned

 

1

 

Remove all material from the plotter.

 

2

 

Ensure that the pinch wheel lever is in the up (open) position.

 

3

 

In the Main Menu, Press F4, Menu 1.

 

4

 

Press F3, Clean?

 

5

 

The ODYSSEY XP checks each of the sensors. Initially, if a problem is
detected, the plotter provides instructions to ensure that material has
been removed and/or that the pinch wheels are up. Follow the
directions on the control panel display to continue.

 Spray air

MAIN MENU

Start-Job

Settings

Mode: Single

Menu 1

Job Status:

Ready

F4

F3

MENU 1

Cut Area

Clean?

Measure

Skew

Enter for Main Menu

F4

F3

Содержание ODYSSEY XP





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды