Gerber ODYSSEY XP Скачать руководство пользователя страница 53

Страница: 53 / 84

Choose the material you want to pounce.

Increase the tool force to 10 ounces, which is 62.50 percent.

Click the Cut/Pounce icon to send the job to the plotter.

To select pounce from the ODYSSEY XP control panel

Attach the pounce cutting strip.

Load the material.

Insert the pounce tool.

Press F3 while holding down the ENTER key for the Operational
Setup menu.

Press F4, Misc.

Press F3, Pounce.

Press F3 or F4 to step through the available pounce patterns:

Short

Medium

Long

, and

Off

Setting

Distance between centers

Short

0.050" (1.3 mm)

Medium

0.200" (5.1 mm)

Long

0.500" (13 mm)

Press ENTER to record the setting and return to Misc Settings menu.

Press ENTER to return to the Main Menu.

Set the tool force to 10 ounces.

Send your pounce job to the plotter.

OPERATIONAL SETUP

Settings

System

Misc.

ENTER for Main Menu

MISC SETTINGS

Repeats

Pounce

Pulldown

Default

ENTER for Main Menu

SELECT POUNCE TYPE

Pouncing:

OFF

ENTER Key to Accept

Содержание ODYSSEY XP





















































































Результаты поиска

Содержание ODYSSEY XP

Отзывы:

Бренды по названию

Популярные бренды

Gerber ODYSSEY XP, Руководство пользователя

Результаты поиска

Содержание ODYSSEY XP

Отзывы:

Бренды по названию

Популярные бренды