manualshive.com logo in svg

Gerber ODYSSEY XP, Руководство пользователя

Поделиться
Скачать
Gerber ODYSSEY XP Скачать руководство пользователя страница 7

1

Chapter 1:
Introduction

Thank you for purchasing the Gerber ODYSSEY

 XP plotter, a state-of-

the-art plotter designed for use with Gerber OMEGA

 and GRAPHIX

ADVANTAGE

 (GA

) software as well as other software using the

HPGL

 command set. In addition to handling and cutting vinyl films

and mask materials, the ODYSSEY XP is specially designed to cut jobs
printed on the GERBER MAXX

 printer.

Features

The ODYSSEY XP plotter has many features that make it easy and
convenient to use:

♦

 

Automatic Material Alignment

 with edge alignment sensors provide

quick and easy loading.

♦

 

Active Material Edge Tracking Control/Slew Control during jobs
assures long-term, accurate cutting and plotting with minimum
supervision.

♦

 

The ODYSSEY XP draws, cuts, and pounces designs on a variety of
material types and dimensions:
Material length 

−

 from 6" (15.2 cm) to as long as a 50 yd (45 m) roll

Material width 

−

 from 5" (12.7 cm) to 52" (132.1 cm)

Maximum cutting width - 49" (124.5 cm)

♦

 

Jobs can be controlled entirely from OMEGA or GA version 6.2.1 or
higher. Selecting a specific material automatically sends the
appropriate tool settings for that material to the ODYSSEY XP.

♦

 

Pounce instructions can be sent from OMEGA or GA 6.2 or higher.

♦

 

The control panel and display provide fast and easy settings
adjustment. Tool settings and other parameters can be made right at
the plotter.

Содержание ODYSSEY XP





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды