manualshive.com logo in svg

Gerber ODYSSEY XP, Руководство пользователя

Поделиться
Скачать
Gerber ODYSSEY XP Скачать руководство пользователя страница 67

61

Error / Failure

Meaning

Correction

32

EEPROM failure

Firmware memory chip
not functioning.

Restore factory defaults.
1.

 

Turn off power.

2.

 

While holding down F1
and CANCEL keys, turn
on power.

3.

 

Retry.

Call Field Service if retry fails.

33

X axis overload

Motion along axis is
jammed or obstructed.

Clear the jam. Retry. Call Field
Service if retry fails.

34

X2 axis overload

Motion along axis is
jammed or obstructed.

Clear the jam. Retry. Call Field
Service if retry fails.

35

Y axis overload

Motion along axis is
jammed or obstructed.

Clear the jam. Retry. Call Field
Service if retry fails.

36

Z axis overload

Motion along axis is
jammed or obstructed.

Clear the jam. Retry. Call Field
Service if retry fails.

37

? axis overload

Unused test

N/A

38

X axis home error

Unused test

N/A

39

Z axis home error

40

Y axis home error

Axis cannot move to
home position.
Excessive friction or
obstruction.

Remove any obstacles to axis
movement.
Retry.
Call Field Service if retry fails.

41

Data overflow error

42

Communications
overrun error

43

Communications
parity error

Invalid, incorrect, or
incompatible
communication setting.

Check communication setting
for compatibility with
computer.

44

Communications
framing error

Invalid, incorrect, or
incompatible
communication setting.

Check communication setting
for compatibility with
computer.

45

No pinch wheel
found

Pinch wheel sensor
malfunction.
Pinch wheel assembly is
loose.

Retry.
Call Field Service if retry fails.

46

Pinch wheel sensor
failure

Pinch wheel sensor
malfunction.

Retry.
Call Field Service if retry fails.

Содержание ODYSSEY XP





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды