manualshive.com logo in svg

Gerber ODYSSEY XP, Руководство пользователя

Поделиться
Скачать
Gerber ODYSSEY XP Скачать руководство пользователя страница 39

33

 

6

 

The selected material will display on the Settings menu and the tool
settings for that material are now set.

 

7

 

Optional

. Press F1 (Default) on the Settings menu to reset all tool

settings for the selected material to the factory presets.

 

8

 

Optional

. You can select changes to tool force and corners on the

Settings menu. See “Tool force” (below) and “Corners” on page 35 for
more information.

Note: Changes to the factory defaults will remain in effect for that material
until you manually reset the modifications to zero or press F1 (Default) in the
Settings menu to restore the factory settings.

 

9

 

Press ENTER again to return to the Main Menu.

Setting the tool force

Tool force is the downward pressure that the tool holder applies to the
material with the tool. Correct force ensures uniform cutting and
drawing. Increased tool force presses harder on the material, but will not
make deeper cuts if the blade exposure is not sufficient. To make deeper
cuts, increase blade exposure. Drawing is also affected by tool force. If
your pen does not make a clear dark line, you can increase the tool force
setting.

You obtain optimum cutting from the plotter by using the least amount
of tool force that will cut the material so that it weeds easily. If you
conclude that an adjustment of the tool force will improve cutting, you
can make the change in the GAPlot32/GSPPlot program. You can also
change the force at the plotter control panel. There are three ways to
change the force:

♦

 

the first way is to make the choice in Gerber software

♦

 

the second way is to make quick, incremental changes at the plotter
control panel (like changing the darkness on a copy machine)

♦

 

the third way is to make specific numeric changes at the plotter
control panel

Auto cutoff tool force is preset and is not affected by changes to tool force
settings.

Observe the following rules:

♦

 

Tool settings sent from Gerber software overrides plotter tool settings

during a job

 unless this feature is turned off either in Gerber software

or in the plotter.

Содержание ODYSSEY XP





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды