General DataComm SC-ADT 16 Por Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 106

background image

SC-ADT Configuration

Port Configuration

3-18

SpectraComm ADT

076R172-000

Installation and Operation Manual

Issue 6

Modem Port Configuration

The SC-ADT front panel Port1 and Port2 can be configured as modem ports (

m0

and

m1

). This

allows these ports to function, in any combination, as:

•

Internal modems (if available)

•

External GDC V.34 modems

•

Bypass modem ports to customer-supplied IP devices (for IP transport - no modem required)

Note

When Port1 and Port2 are configured as internal and/or external modem ports, both modems are locked to
the same DTE rate of 115,200 kbps. When one modem port is configured as an internal/external modem port
and the other as a bypass modem port, the DTE rate for both ports is locked to the bypass rate set by the user.

Cabling and configuration procedures vary, depending on the desired application.
For online help in configuring external, internal and bypass modem modes, type:

configure modem ?

Figure 3-4

Modem Help Displays

Internal/External Modem Configuration Procedure

1. Check that the internal and/or external modems are properly connected to the PSTN. If

applicable, check that any external modems are properly connected to Port1 and/or Port 2.
Refer to Chapter 2 under

Modem Connections

as needed.

2.

Check that any port intended for external modem use is not currently in use as a Term or Tranport port.

3. Configure each modem interface (required for dial-in networking) by typing:

configure interfaces ip-address modem

[0 or 1]

[###.###.###.###] [###.###.###.###]

For example:

configure interfaces ip-address modem0 172.16.5.6 255.255.0.0

configure interfaces ip-address modem1 172.16.5.7 255.255.0.0

4. Enter a description for each modem interface by typing:

configure interfaces description modem

[0 or 1]

[your_description]

For example:

configure interfaces description modem0

“NOC Int Modem”

configure interfaces description modem1

“NOC Ext Modem”

5. Enable the modem interfaces by typing:

configure interfaces enable modem0

configure interfaces enable modem1

Note

If your SC-ADT device is not equipped with integral modems and is not attached to compatible external
modems, the modem interfaces will remain disabled.

ADT-16% configure modem ?
___________Help for "configure modem "______________________
callback Configure modem call back list
mode Set modem operation mode
use Set modem use to internal/external/bypass
bypass Set bypass parameters
caller-id Configure modem caller-id
authen Authentication enable/disable
inactivity Set Dialup Networking inactivity timer; requires 2 parameter(s

«
...
54
55
56
57
58
...
»

Содержание SC-ADT 16 Por











































































































Отзывы:

Нет отзывов

Похожие инструкции для SC-ADT 16 Por

Бренд: Palm Страницы: 4

grandMA2 Series

Бренд: MA lighting Страницы: 36

Бренд: Lorex Страницы: 186

Бренд: Axis Страницы: 104

Бренд: Intel Страницы: 108

inLab Speedcure 9494800

Бренд: Dentsply Sirona Страницы: 91

Бренд: Delta Страницы: 2

PARTNER Voice Messaging PC Card Release 2

Бренд: Lucent Technologies Страницы: 67

Бренд: ekwb Страницы: 2

Бренд: Idis Страницы: 31

Бренд: Tripp Lite Страницы: 3

Optane Persistent Memory 200 Series

Бренд: Supermicro Страницы: 54

Бренд: C&T Solution Страницы: 129

RP614 - Web Safe Router

Бренд: NETGEAR Страницы: 16

RADEON 9800 PRO

Бренд: ATI Technologies Страницы: 20

Бренд: Maipu Страницы: 26

E5345 - Xeon 2.33 GHz 8M L2 Cache 1333MHz FSB LGA771 Active Quad-Core Processor

Бренд: Intel Страницы: 112

Бренд: FiberHome Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды