manualshive.com logo in svg

GE L90, Инструкция по эксплуатации

"Jet L90" - это мощный и надежный продукт, который упрощает работу оператора. Бесплатно загрузите Руководство оператора для "Jet L90" на manualshive.com. Получите подробные инструкции по использованию этого устройства для оптимальной производительности. Не упустите возможность улучшить свой опыт работы с "Jet L90".

Поделиться
Скачать
background image

5-114

L90 LINE CURRENT DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL

PRODUCT SETUP

CHAPTER 5: SETTINGS

5

The L90 incorporates a multi-ended fault locator method based on the synchronized voltage and current measurements 
at all ends of the transmission line. This makes it possible to compute the fault location without assumptions or 
approximations. This fault locator method is applicable on both two-terminal and three-terminal applications, with results 
computed independently at each terminal. For three-terminal line applications, the fault locator is reports the exact line 
segment at which the fault occurred and the distance to the fault from the terminal adjacent to the fault.
if charging current compensation is configured and enabled, the line charging current is removed at each terminal for 
improved accuracy.
During communication channel failures, the L90 uses the single-ended algorithm to calculate and report fault location. 
When the single-ended algorithm is used for three-terminal line applications, the faulted segment of the line is not 
determined and reported.
The L90 relay supports one fault report and an associated fault locator per CT bank to a maximum of four. The signal 
source and trigger condition, as well as the characteristics of the line or feeder, are entered in this menu.
The fault report stores data, in non-volatile memory, pertinent to an event when triggered. The captured data contained in 
the FaultReport.txt file includes:
•

Fault report number

•

Name of the relay, programmed by the user

•

Firmware revision of the relay

•

Date and time of trigger

•

Name of trigger (specific operand)

•

Line or feeder ID via the name of a configured signal source

•

Active setting group at the time of trigger

•

Pre-fault current and voltage phasors (two cycles before either a 50DD disturbance associated with fault report 
source or the trigger operate). Once a disturbance is detected, pre-fault phasors hold for three seconds waiting for the 
fault report trigger. If trigger does not occur within this time, the values are cleared to prepare for the next disturbance.

•

Fault current and voltage phasors (one cycle after the trigger)

•

Elements operated at the time of triggering

•

Events — Nine before trigger and seven after trigger (only available via the relay web page)

•

Fault duration times for each breaker (created by the breaker arcing current feature)

The captured data also includes the fault type, the distance to the fault location, distance to the fault location, fault loop 
impedance, as well as the reclose shot number (when applicable). To include fault duration times in the fault report, enable 
and configure the breaker arcing current feature for each of the breakers. Fault duration is reported on a per-phase basis.
The relay allows locating faults, including ground faults, from delta-connected VTs. In this case, the missing zero-sequence 
voltage is substituted either by the externally provided neutral voltage (broken delta VT) connected to the auxiliary voltage 
channel of a VT bank, or by the zero-sequence voltage approximated as a voltage drop developed by the zero-sequence 
current, and user-provided zero-sequence equivalent impedance of the system behind the relay.
The trigger can be any FlexLogic operand, but in most applications it is expected to be the same operand, usually a virtual 
output, that is used to drive an output relay to trip a breaker. To prevent the overwriting of fault events, do not use the 
disturbance detector to trigger a fault report. A FAULT RPT TRIG event is automatically created when the report is triggered.
If a number of protection elements are ORed to create a fault report trigger, the first operation of any element causing the 
OR gate output to become high triggers a fault report. However, If other elements operate during the fault and the first 
operated element has not been reset (the OR gate output is still high), the fault report is not triggered again. Considering 
the reset time of protection elements, there is very little chance that a fault report can be triggered twice in this manner. As 
the fault report must capture a usable amount of pre and post-fault data, it cannot be triggered faster than every 20 ms.
Each fault report is stored as a file; the relay capacity is 15 files. A 16th trigger overwrites the oldest file.
Individual fault report features store their files in the same memory space. The sixteenth report overwrites the first one 
regardless of which fault report feature produced the sixteenth and the first records.

FAULT REPORT 1 Z0M

MAG: 0.00 

Ω

Range:  0.00 to 650.00 ohms in steps of 0.01

Содержание L90





































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для L90

Nidec Leroy-Somer R180 Installation And Maintenance Manual preview
Leroy-Somer R180
Бренд: Nidec Страницы: 20
CAME G5000 Installation, Operation And Maintenance Manual preview
G5000
Бренд: CAME Страницы: 32
Babybee Prams Comet Instruction Manual preview
Comet
Бренд: Babybee Prams Страницы: 21
Panasonic FP2 Series Technical Manual preview
FP2 Series
Бренд: Panasonic Страницы: 68
Panasonic GP-KS162CUDE Operating Instruction preview
GP-KS162CUDE
Бренд: Panasonic Страницы: 27
Panasonic EBL512 G3 5000 Planning Instructions preview
EBL512 G3 5000
Бренд: Panasonic Страницы: 168
Panasonic WV-CU980 Software Update Procedure preview
WV-CU980
Бренд: Panasonic Страницы: 8
Panasonic AW-RP50 Manual preview
AW-RP50
Бренд: Panasonic Страницы: 3
Panasonic FP0H Series Operation Manual preview
FP0H Series
Бренд: Panasonic Страницы: 20
Panasonic AK-HRP1010G Operating Manual preview
AK-HRP1010G
Бренд: Panasonic Страницы: 29
Panasonic AK-HRP1005G Operation Manual preview
AK-HRP1005G
Бренд: Panasonic Страницы: 37
Panasonic AG-EC4G Operating Instructions Manual preview
AG-EC4G
Бренд: Panasonic Страницы: 9
Vasco RF User And Installation Manual preview
RF
Бренд: Vasco Страницы: 32
Abra AK-10 User Manual preview
AK-10
Бренд: Abra Страницы: 16
SAI Connect Operation Manual preview
Connect
Бренд: SAI Страницы: 16
Hable One Starting Manual preview
One
Бренд: Hable Страницы: 3
Danfoss VLT AQUA Drive FC 202 Installation Manual preview
VLT AQUA Drive FC 202
Бренд: Danfoss Страницы: 124
Danfoss AME 55 Installation Manual preview
AME 55
Бренд: Danfoss Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды