manualshive.com logo in svg

GE L90, Инструкция по эксплуатации

"Jet L90" - это мощный и надежный продукт, который упрощает работу оператора. Бесплатно загрузите Руководство оператора для "Jet L90" на manualshive.com. Получите подробные инструкции по использованию этого устройства для оптимальной производительности. Не упустите возможность улучшить свой опыт работы с "Jet L90".

Поделиться
Скачать
background image

CHAPTER 8: APPLICATION OF SETTINGS

PROTECTION SIGNALING SCHEMES

L90 LINE CURRENT DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL

8-19

8

The output operand from the scheme (HYBRID POTT OP) must be configured to interface with other relay functions, output 
contacts in particular, in order to make the scheme fully operational. Typically, the output operand is programmed to 
initiate a trip, breaker fail, and auto-reclose, and to drive a user-programmable LED as per user application.

8.5.6  Directional comparison blocking

The scheme compares the direction to a fault at both ends of the line. Unlike the permissive schemes, the absence of a 
blocking signal permits operation of the scheme. Consequently, the scheme is biased toward dependability and requires 
an “on/off” type of signaling.
By default, this scheme uses only a forward-looking over-reaching Zone 2 distance element to identify forward faults. 
Ground directional overcurrent functions available in the relay can be used in conjunction with the Zone 2 distance 
element to increase the coverage for high-resistance faults.
By default, the scheme uses only a reverse-looking Zone 4 distance element to identify reverse faults. Ground directional 
overcurrent functions available in the relay can be used in conjunction with the Zone 4 distance element for better time 
and sensitivity coordination.
For proper operation of the scheme, the Zone 2 and 4 phase and ground distance elements must be enabled and 
configured per rules of distance relaying.
If used by this scheme, the selected ground directional overcurrent function(s) must be enabled and configured 
accordingly.
The scheme generates output operands (BLOCKING SCHEME TX INIT and BLOCKING SCHEME TX STOP) that are used 
control the transmission of signals to the remote end. Choices of communications channel include Remote Inputs/Outputs 
and telecommunications interfaces. When used with telecommunications facilities, assign the output operand to operate 
an output contact connected to key the transmitter at the interface.
A blocking scheme can be preferred over a Hybrid POTT scheme, because of shorter reach settings for the Zone 2 
elements. This follows from the fundamental difference that all zone 2 elements are required to see an internal fault for the 
POTT approach, under all system conditions, which in turn, means that the reversed Zone 4 block initiate elements must 
also have an increased reach. A blocking scheme on the other hand, can have much shorter Zone 2 reach settings if 
sequential clearance can be accepted. The simple rule to ensure that all faults can be cleared, is for each terminal to have 
a reach setting equal to the distance to the tap plus twice the distance from the tap to the remote terminal.
The Zone 2 element must have a coordinating timer 

BLOCK RX CO-ORD PKP DELAY

, to ensure that the blocking signal is 

received for all external faults that are within the set reach of the local overreaching Zone 2.
Transient blocking logic is implemented via the 

TRANS BLOCK

 timer, which continues to send a blocking signal for a settable 

time 

TRANS BLOCK RESET DELAY

, if it was being sent for at least 30 ms during the initial reverse fault set via 

TRANS BLOCK 

PICKUP DELAY

.

The output operand from the scheme (BLOCKING SCHEME OP) must be configured to interface with other relay functions, 
output contacts in particular, in order to make the scheme fully operational. Typically, the output operand is programmed 
to initiate a trip, breaker fail, and auto-reclose, and to drive a user-programmable LED as per user application.

8.5.7  Directional comparison unblocking

8.5.7.1  Overview

The directional comparison unblocking scheme is used with a frequency shift keying (FSK) PLC that produces a loss-of-
guard output during an actual loss-of-guard signal condition and during reception of the permissive keyed frequency 
when the received carrier signal changed from guard to permissive frequency. The loss-of-guard signal is preferably a 
normally-closed contact, allowing the scheme to get this signal if the communications equipment failed. This loss-of-
guard output is connected to a contact input of the L90. The power line carrier also provides an output contact when the 
permissive frequency is received. This output is wired to any other contact input of the L90.

Содержание L90





































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для L90

OmarLift C40 Instruction Manual preview
C40
Бренд: OmarLift Страницы: 14
VADDIO EVI-D70 Installation And User Manual preview
EVI-D70
Бренд: VADDIO Страницы: 2
Daikin ALTHERMA User Manual preview
ALTHERMA
Бренд: Daikin Страницы: 5
Fancom 743 Installer Manual preview
743
Бренд: Fancom Страницы: 31
3M SST Manual preview
SST
Бренд: 3M Страницы: 90
GCE S 400 Operating Instructions Manual preview
S 400
Бренд: GCE Страницы: 24
H3C S9500E Series Card Manual preview
S9500E Series
Бренд: H3C Страницы: 5
H3C WX1800H series Command Reference Manual preview
WX1800H series
Бренд: H3C Страницы: 27
H3C WX3500H series Installations preview
WX3500H series
Бренд: H3C Страницы: 4
H3C WX5540H Installation Manual preview
WX5540H
Бренд: H3C Страницы: 54
H3C LSWM1WCM10 Manual preview
LSWM1WCM10
Бренд: H3C Страницы: 10
H3C LSQM1WCMB0 Quick Start Manual preview
LSQM1WCMB0
Бренд: H3C Страницы: 10
NAPCO Gemini GEM-P9600 Installation Instructions Manual preview
Gemini GEM-P9600
Бренд: NAPCO Страницы: 6
NAPCO Gemini GEM-P816 Programming Instructions Manual preview
Gemini GEM-P816
Бренд: NAPCO Страницы: 56
Packard Bell Slim Remote Control Instruction preview
Slim Remote Control
Бренд: Packard Bell Страницы: 2
Unipower PCM500 Series Operating Manual preview
PCM500 Series
Бренд: Unipower Страницы: 24
M-system R5-TS Instruction Manual preview
R5-TS
Бренд: M-system Страницы: 3
SYCLOPE electronic TRACE'O Installation And Starting Instructions preview
TRACE'O
Бренд: SYCLOPE electronic Страницы: 40

Бренды по названию

Популярные бренды

Загрузить еще бренды