Foma D702i, Руководство пользователя

Страница: 399 / 405

26
AT command list
･
When AT commands are input, entering “ ￥ ” may cause “ \ ” to appear depending on the font settings
for the PC or communication software in use.
･
If the battery pack is removed from FOMA terminal before the terminal power is turned off, the setting
values may not be recorded.
･
AT commands that can be used via the FOMA D702i Modem Port are described in this list.
*1 : Returns the setting to default with the AT & F command.
*2 : Stores the command setting into FOMA terminal with the AT&W command and restores it with the ATZ command.
None : Indicates the AT command does not include any display command or test command.
[
] : Indicates the parameter can be omitted.
Command Description & Parameter
AT%V Shows the version of your FOMA terminal in the format of “Verx.xx”.
ex. Enter AT%V Display None Test None
AT&C [n] Selects the operational conditions of the circuit CD signal outgoing to DTE.
n=0: The circuit CD signal is always on. (when parameter omitted)
n=1: The circuit CD signal varies depending on the other modem. (default)
*1, *2 ex. Enter AT&C1 Display None Test None
AT&D [n] Determines an action to be taken when the circuit ER signal coming from DTE changes from on to off
in the online data mode.
n=0: Ignores the ER signal condition (always on). (when parameter omitted)
n=1: Switches the mode to the online command mode when the ER signal changes from on to off.
n=2: Disconnects the circuit and switches the mode to the offline mode when the ER signal changes
from on to off. (default)
*1, *2 ex. Enter AT&D1 Display None Test None
AT&E [n] Selects type of speed display used when connection is made.
This command is effective only when the ATX command is other than “n=0”.
n=0: Displays communication speed of wireless zone.
n=1: Displays communication speed between PC and FOMA terminal. (default)
*1, *2 ex. Enter AT&E1 Display None Test None
AT&F [0] Resets all FOMA terminal state to the default. When executed while receiving a call, it resets FOMA
terminal state to the default without affecting the call. When executed during communication, the
terminal state returns to default after it disconnects the communication.
ex. Enter AT&F0 Display None Test None
AT&S [n] Determines the control of the DR signal FOMA terminal outputs.
n=0: Always on. (default and when parameter omitted)
n=1: The DR signal turns on when the circuit is connected.
*1, *2 ex. Enter AT&S0 Display None Test None
AT&W [0] Writes the current settings into FOMA terminal.
ex. Enter AT&W0 Display None Test None
AT ＊ DANTE Shows the signal strength (reception level) in the format of “ ＊ DANTE:m”.
m=0: Outside the service area m=1 to 3: Number of antennas displayed on FOMA terminal
ex. Enter AT
＊
DANTE Display AT
＊
DANTE? Test AT
＊
DANTE=?
AT
＊
DGANSM=n Specifies whether to reject or accept an incoming packet call.
n=0: Sets both the incoming call rejection and the incoming call acceptance off. (default)
n=1: Sets the incoming call rejection on. n=2: Sets the incoming call acceptance on.
ex. Enter AT ＊ DGANSM=0 Display AT ＊ DGANSM? Test AT ＊ DGANSM=?
AT ＊ DGAPL=n [,cid] Specifies dialup connections (APNs) to accept incoming packet calls from them. For an APN, use the
cid parameter defined with “+CGDCONT”.
n=0: Adds the APN defined with the cid parameter to the call acceptance list.
n=1: Deletes the APN defined with the cid parameter from the call acceptance list.
When you omit the cid parameter, all cids will be added or deleted.
ex. Enter AT ＊ DGAPL=0,1 Display AT ＊ DGAPL? Test AT ＊ DGAPL=?
AT ＊ DGARL=n [,cid] Specifies dialup connections (APNs) to reject incoming packet calls from them. For an APN, use the
cid parameter defined with “+CGDCONT”.
n=0: Adds the APN defined with the cid parameter to the call rejection list.
n=1: Deletes the APN defined with the cid parameter from the call rejection list.
When you omit the cid parameter, all cids will be added or deleted.
ex. Enter AT ＊ DGARL=0,1 Display AT ＊ DGARL? Test AT ＊ DGARL=?
Next
Manual for Data Communication.fm 26 ページ ２００６年１月２７日 金曜日 午前１１時４１分