Flight Medical Innovations 60 DL Скачать руководство пользователя страница 81

Страница: 81 / 113

Calibration and Verification tests

Calibration

Flight 60 Service Manual

7-11

7.1.4 Oxygen Sensor Calibration

To calibrate the Oxygen sensor:

For iO

internal mixer model

Connect a high pressure oxygen hose to the High Pressure O2 port

Connect a calibrated Oxygen Analyzer to the ventilator's outlet.

Don't connect

a patient circuit!

Press

Technical

and then press

ADVANCED Screen

Enter the code

5844

, and confirm by pressing



Press

SERVICE SCREEN

Press

Calibrate FiO2.

Choose

USED

if calibrating the current sensor,

NEW

if O

sensor is replaced.

The ventilator performs 21% calibration. Verify the external Oxygen analyzer
reads 21%, wait 1 minute and press Enter /

The ventilator switches to 100% automatically. Verify the external Oxygen
analyzer reads 100%, wait 1 minute and press Enter /

For External mixer model

Connect the Air/Oxygen Entrainment Mixer to an Oxygen source. Install the
Air/Oxygen Entrainment Mixer on the ventilator’s air inlet.

Set the regulator on the oxygen source to

PSI.

Connect a calibrated Oxygen Analyzer to the ventilator's outlet.

Don't connect

a patient circuit!

Press

Technical

and then press

ADVANCED Screen

Enter the code

5844

, and confirm by pressing



Press

SERVICE SCREEN

Press

Calibrate FiO2.

Choose

USED

if calibrating the current sensor,

NEW

if O

sensor is replaced.

Set the Entrainment Mixer dial to AIR.

10.

Once the external Oxygen sensor displays 21%, wait 1 minute and then press
Enter /

11.

Set the Entrainment Mixer dial to 100%.

Содержание 60 DL


















































































































Результаты поиска

Содержание 60 DL

Отзывы:

Бренды по названию

Популярные бренды

Flight Medical Innovations 60 DL, Руководство по обслуживанию

Результаты поиска

Содержание 60 DL

Отзывы:

Бренды по названию

Популярные бренды