Flight Medical Innovations 60 DL Скачать руководство пользователя страница 19

Страница: 19 / 113

Functional Description

Front Panel

Flight 60 Service Manual

3-3

Item

Symbol

Description

2 - Manual Breath

Delivers a user initiated manual inflation.

3 – Panel Lock

Enables the user to lock the ventilator’s control,
preventing accidental changes. Pressing the button of a
locked panel and then Enter, unlocks the panel.

4 – Cancel

Enable the user to cancel parameters change.

5 – Increase
Button

Enables the user to adjust setting parameters upwards.

6 – Decrease
Button

Enables the user to adjust setting parameters
downwards.

7 – OK (Enter)

Enable the user to confirm parameters or mode change.

8 – On/Off

Turns the ventilator on or off, to start or stop ventilation.

9 – Alarm Reset

The Alarm Reset silences the audible alarm and clears lit
alarm LEDs.

10 – Technical

Technical data and selection options.

11 – Extended

Additional ventilation parameters screen.

3.1.2 LED Indicators

The LED indicators on the front panel inform the user of various events.

The following table describes the available LED indicators.

LED Indicator

Description

TRIG

Green LED indicates a patient’s breathing effort.

EXT PWR

Yellow LED indicates that an external power source is being applied to the ventilator.

LOW BAT

Red LED indicates that total batteries charge level is below 50%.

BAT

Orange LED indicates that the ventilator is powered on batteries.

FAULT

Red LED indicates a ventilator malfunction.

APNEA

Red LED indicates that no breaths have been delivered for the preset APNEA interval.

BUV

Red LED indicates that backup ventilation is active.

HIGH MV

Red LED indicates that the high inspiratory minute volume alarm limit is being violated.

LOW MV

Red LED indicates that the low inspiratory minute volume alarm limit is being violated.

HIGH P

Red LED indicates that the high peak airway pressure alarm limit is being violated.

Содержание 60 DL


















































































































Результаты поиска

Содержание 60 DL

Отзывы:

Бренды по названию

Популярные бренды

Flight Medical Innovations 60 DL, Руководство по обслуживанию

Результаты поиска

Содержание 60 DL

Отзывы:

Бренды по названию

Популярные бренды