Flight Medical Innovations 60 DL Скачать руководство пользователя страница 66

Страница: 66 / 113

Removing and Reinstalling Modules

Replacing the Lower Board and D-type Board

4-36

| FLIGHT 60 Service Manual

Figure 64 – Detaching the Solenoid Bracket

Remove the 2 screws securing the solenoid to the bracket. Pull out the
solenoid from the bracket. Verify the sealant O-ring is removed and is not
attached to the bracket.

4.19.2 Installing the Solenoid Assembly

To install the solenoid assembly:



Follow the above procedure in reverse order.

Replacing the Lower Board and D-type Board

4.20.1 Removing the Lower Board and D-type Board

To remove the Lower and D-type boards:

1. Remove the detachable battery (see section 4.3) and the internal battery (see

section 4.4).

2. Remove the ventilator cover (see section 4.5).

3. Remove the front panel assembly (see section 4.8).

4. Remove the Power board (see section 4.6)

5. Remove the Power Supply and its base plate (see section 4.7)

6. Remove the internal O2 mixer (see section 4.15)

7. Remove the Manifold assembly (see section 4.11)

9. Unscrew the 2 Torx screws (plastic washers) securing the Outlet assembly.

Remove the Outlet assembly.

Содержание 60 DL


















































































































Результаты поиска

Содержание 60 DL

Отзывы:

Бренды по названию

Популярные бренды

Flight Medical Innovations 60 DL, Руководство по обслуживанию

Результаты поиска

Содержание 60 DL

Отзывы:

Бренды по названию

Популярные бренды