FEC AFC3000, Руководство по эксплуатации оборудования

Страница: 165 / 294

Chapter 6 Power up and Initial Checks
PAGE 6-2
6-1 Power Activation
・ ・ ・ ・
Operational Test
WARNING
DO NOT operate the system WITHOUT all safety guards and/or devices in place and
operational.
Follow Lockout/Tagout and other safety precautions when performing maintenance or
connecting / disconnecting cabling, wiring, and equipment.
There is a possibility of electrical shock from this equipment if used improperly.
6-1-1 Before Powering On
•
Verify MFC Controller Rotary/DIP switch settings (Section 4-12)
Verify that the (2) rotary switches visible on the front of each controller are set to indicate the
appropriate spindle number.
Verify that SW1 and SW2 loacted on the front and bottom of the controller are set to indicate the
appropriate function and options.
•
Check connection between tool and controller (Section 4-5)
Verify that the homerun and extension cables (resolver, motor and transducer) connecting the tool to
the MFC controller are secure. Ensure that each numbered set of cables are connected to the
identically numbered tool and MFC controller.
If the application requires the tool mounting fixture to move, visually inspect all components to ensure
that there is proper clearance and that cables have sufficient length. If movement would create any
excessive stress on a cable or create any potential for damage to the system, then make appropriate
adjustments. Confirm the bend radius of any tool cable(s) are more than 6” (min) and follow cabling
guidelines.
WARNING: DO NOT make motor connections with the power on. Turn off all controller power
before attempting to connect or disconnect any motor cables or system damage may occur.
•
Check MFC Controller I/O cable wiring (Section 4-6)
Connections with external control equipment are done between MFC Controller I/O connectors and/or
(Fieldbus) Expansion unit I/O connectors.
Verify that the I/O interface wiring is connected to the corresponding PLC terminals.
•
Check the Input Voltages (Section 2-1, 4-4)
Verify that the Input Power Connectors (Main and 24VDC Control) are properly wired and that the
voltage to be applied is within the specified range.
Verify that the 24VDC and 0VDC common wires are properly connected.
Damage may occur if
wired improperly.
A A A A
A A A A
l ll l
l ll l
w w w w
w w w w
a a a a
a a a a
y y y y
y y y y
s s s s
s s s s
v v v v
v v v v
e e e e
e e e e
r r r r
r r r r
i ii i
i ii i
f f f f
f f f f
y y y y
y y y y
t t t t
t t t t
h h h h
h h h h
e e e e
e e e e
i ii i
i ii i
t t t t
t t t t
e e e e
e e e e
m m m m
m m m m
s s s s
s s s s
a a a a
a a a a
b b b b
b b b b
o o o o
o o o o
v v v v
v v v v
e e e e
e e e e
b b b b
b b b b
e e e e
e e e e
f f f f
f f f f
o o o o
o o o o
r r r r
r r r r
e e e e
e e e e
p p p p
p p p p
o o o o
o o o o
w w w w
w w w w
e e e e
e e e e
r r r r
r r r r
i ii i
i ii i
n n n n
n n n n
g g g g
g g g g
o o o o
o o o o
n n n n
n n n n
•
Power Voltage Re-Checks
Re-check the input power voltage after turning the power on to make sure the voltage does not drop
due to loading.
Check again for loading when the spindle has started and the torque is at its maximum level for the
fastening cycle (maximum power consumption time).