Endress+Hauser Fieldgate FXA42 Скачать руководство пользователя

Страница: 107 / 118

Fieldgate FXA42

Diagnostics and troubleshooting

Hauser

107

Diagnostics and troubleshooting

9.1

Faults indicated by the LEDs

WARNING

Danger! Electric voltage!

Risk of electric shock and injury from startle response.

‣

De-energize all power sources before disconnecting and connecting.

‣

Only work with insulated tools.

The

Power

LED is not lit.

Possible cause: No power

• Action: Check to ensure that the power supply is wired correctly

• Action: Check to ensure that the supply voltage corresponds to the voltage indicated on

the nameplate

• Action: Check to ensure that the power is switched on
The

modem / WLAN / Ethernet

LED is not lit.

Possible cause: The power supply for the modem / WLAN unit / Ethernet interface is

interrupted

Action: Switch off the power supply, wait 30 s seconds, then switch the power supply back

on
The

Network

LED is not lit.

Possible cause: Fieldgate FXA42 Ethernet: the Ethernet data connection is interrupted. A

valid fixed IP address has not been configured or DHCP was not completed successfully.

• Action: Check to ensure that the configured IP address is valid

• Action: Check to ensure that the dynamic allocation of IP addresses (DHCP) works

correctly in the connected network

• Action: Check to ensure that the Ethernet connections are correctly engaged and that

the cables are OK

9.2

Restoring factory settings

The reset button (→  8) can be accessed through a small hole in the front.

1. Switch off the Fieldgate FXA42 (switch off the supply voltage).
2. Press and hold the reset button.
3. Switch on the Fieldgate FXA42. Keep the reset button pressed during the booting

procedure.
 The factory settings are restored.

Maintenance

No special maintenance work is required.

10.1 Exterior cleaning

Clean the device with a dry cloth.

NOTICE

Caustic cleaning agents or solvents corrode surfaces.

Important information on the housing may become illegible, surfaces become corroded.

‣

Do not use caustic cleaning agents or solvents.

Содержание Fieldgate FXA42























































































































Результаты поиска

Содержание Fieldgate FXA42

Отзывы:

Похожие инструкции для Fieldgate FXA42

Бренды по названию

Популярные бренды

Endress+Hauser Fieldgate FXA42, Руководство по эксплуатации

Результаты поиска

Содержание Fieldgate FXA42

Отзывы:

Похожие инструкции для Fieldgate FXA42

Бренды по названию

Популярные бренды