Endress+Hauser Fieldgate FXA42 Скачать руководство пользователя

Страница: 73 / 118

Fieldgate FXA42

Operation

Hauser

The connection supervision has failed to connect to the configured URLs. The connection

will be closed.

Modem reset

The cellular modem hardware has been reset.

Hanging! (state: <x>)

The cellular modem driver is in an invalid state.

8.4.5

WLAN

If the device has a WLAN interface, it can be activated and configured on this page.

Settings

The following table describes the available settings for the WLAN unit.

Settings

Description

Enable WLAN

Enables the module.

SSID

Network name/identifier (0-32 printable characters). If no SSID is specified, the driver stops
its association attempts.

Security

Select a security method: Open, WEP128 or WPA(2)-PSK (recommended).

WPA passphrase The passphrase for WPA(2)-PSK security can consist of 8-63 characters.

WEP128

If the WEP128 security mode is chosen, a valid WEP key (26 Hex characters) has to be
entered in the selected key index field.

Use DHCP

If this option is set, the module gets its IP configuration through DHCP.

IP address

IP address for the WLAN interface.

IP netmask

Netmask for the WLAN interface.

Only modify the WLAN settings via the Ethernet (hard-wired) connection, wherever

possible! If the configuration is changed via the WLAN connection itself, this may

cause the connection that is currently established to be lost after a device restart.

Wireless scanning

Press the

Scan

button to search for available wireless networks.

The scan takes about 20 seconds. Afterwards the wireless networks found are shown in a

dialog.
Select the desired wireless network using the

Select

button or by double-clicking the

corresponding entry. The settings of the selected wireless network are applied to the

configuration page. Enter the WPA passphrase and the WEP key if necessary.

Event log messages

The following section describes the messages that the WLAN driver may log to the event

log. All messages are prefixed with the text

WLAN Driver

Started

The WLAN unit driver has been started.

Running

The WLAN unit driver is now running.

Configured IP through DHCP

The WLAN unit driver has configured its IP address through the DHCP protocol.

Stopping driver

Содержание Fieldgate FXA42























































































































Результаты поиска

Содержание Fieldgate FXA42

Отзывы:

Похожие инструкции для Fieldgate FXA42

Бренды по названию

Популярные бренды

Endress+Hauser Fieldgate FXA42, Руководство по эксплуатации

Результаты поиска

Содержание Fieldgate FXA42

Отзывы:

Похожие инструкции для Fieldgate FXA42

Бренды по названию

Популярные бренды