Endress+Hauser Fieldgate FXA42 страница 36 Скачать руководство пользователя

Страница: 36 / 118

Commissioning

Fieldgate FXA42

Hauser

7.5.6

Configuration with Modbus RS485

A0030923

 7

System architecture of a Fieldgate FXA42 with Modbus RS485

SupplyCare Enterprise / SupplyCare Hosting (via Web browser)

Internet / LAN

SupplyCare Enterprise / SupplyCare Hosting on mobile devices (via Web browser)

Ethernet / WLAN / UMTS / LTE Cat M1 / LTE Cat NB1

Fieldgate FXA42

Power supply 24 V

1 x Modbus RS485 as master or slave

4 x analog input 4 to 20 mA (2-wire / 4-wire)

The Modbus RS485 connection can be used as either a master or a slave, but cannot

act as both simultaneously.

• When operated as a master, up to 32 devices and 256 values can be defined. As

values can become arrays when reading and writing several registers or coils, the

following limit applies: The number of all scalar (non-array) values plus the size of

all arrays must not exceed 512.

• When operated as a slave, up to 128 values can be defined. As values can become

arrays when reading and writing several registers or coils, the following limit

applies: The number of all scalar (non-array) values plus the size of all arrays must

not exceed 512.

Configuration of FXA42 as a Modbus RS485 master (reading out data from other

systems)

1. Open the Settings page .
2. Select the

Modbus client/master

tab.

Содержание Fieldgate FXA42























































































































Результаты поиска

Содержание Fieldgate FXA42

Отзывы:

Похожие инструкции для Fieldgate FXA42

Бренды по названию

Популярные бренды

Endress+Hauser Fieldgate FXA42, Руководство по эксплуатации

Результаты поиска

Содержание Fieldgate FXA42

Отзывы:

Похожие инструкции для Fieldgate FXA42

Бренды по названию

Популярные бренды