Endress+Hauser Dosimag Скачать руководство пользователя страница 18

Страница: 18 / 76

Installation

Dosimag

Hauser

Horizontal

A0025817

Measuring electrodes

The measuring electrode plane must be horizontal. This prevents brief insulation of

the two measuring electrodes by entrained air bubbles.

High temperatures

A0003830

 5

Recommended orientation in the event of strong heat formation

To prevent the electronics from overheating in the event of strong heat formation

(e.g. CIP or SIP cleaning process), install the measuring device with the transmitter

part pointing downwards.

Inlet and outlet runs

If possible, install the sensor upstream from fittings such as valves, T-pieces or elbows.
Observe the following inlet and outlet runs to comply with accuracy specifications:

5 × DN

≥

2 × DN

≥

A0016275

Installation dimensions

For the dimensions and installation lengths of the device, see the "Technical

Information" document, "Mechanical construction" section

Содержание Dosimag













































































Результаты поиска

Содержание Dosimag

Отзывы:

Похожие инструкции для Dosimag

Бренды по названию

Популярные бренды

Endress+Hauser Dosimag, Руководство по эксплуатации

Результаты поиска

Содержание Dosimag

Отзывы:

Похожие инструкции для Dosimag

Бренды по названию

Популярные бренды