Endress+Hauser Dosimag Скачать руководство пользователя страница 21

Страница: 21 / 76

Dosimag

Installation

Hauser

Linear filling system

A0003762

Measuring device

Tank

Batching valve

Vessel

6.2

Mounting the measuring device

6.2.1

Required tools

For sensor

For flanges and other process connections:

• Screws, nuts, seals etc. are not included in the scope of supply and must be provided by

the customer.

• Appropriate mounting tools

6.2.2

Preparing the measuring device

1. Remove all remaining transport packaging.
2. Remove any protective covers or protective caps present from the sensor.
3. Remove stick-on label on the electronics compartment cover.

6.2.3

Mounting the measuring device

WARNING

Danger due to improper process sealing!

‣

Ensure that the inside diameters of the gaskets are greater than or equal to that of the

process connections and piping.

‣

Ensure that the gaskets are clean and undamaged.

‣

Install the gaskets correctly.

Depending on the order option, the measuring device is supplied with or without pre-

installed process connections. Pre-installed process connections are secured to the

measuring device using 4 hexagonal-headed bolts.

‣

Ensure that the direction of the arrow on the nameplate of the sensor matches the flow

direction of the fluid.

Depending on the application and pipe length, the measuring device may need to be

supported or additionally secured.

Содержание Dosimag













































































Результаты поиска

Содержание Dosimag

Отзывы:

Похожие инструкции для Dosimag

Бренды по названию

Популярные бренды

Endress+Hauser Dosimag, Руководство по эксплуатации

Результаты поиска

Содержание Dosimag

Отзывы:

Похожие инструкции для Dosimag

Бренды по названию

Популярные бренды