Endress+Hauser Dosimag Скачать руководство пользователя страница 24

Страница: 24 / 76

Electrical connection

Dosimag

Hauser

Electrical connection

The measuring device does not have an internal circuit breaker. For this reason,

assign the measuring device a switch or power-circuit breaker so that the power

supply line can be easily disconnected from the mains.

7.1

Connection conditions

7.1.1

Requirements for connecting cable

The connecting cables provided by the customer must fulfill the following requirements.

Electrical safety

In accordance with applicable federal/national regulations.

Permitted temperature range

• –40 °C (–40 °F) to +80 °C (+176 °F)

• Minimum requirement: cable temperature range ≥ ambient tempe20 K

Signal cable

Cables are not included in the scope of delivery; they can be ordered as an accessory

→  57.

Pulse/frequency/switch output

Standard installation cable is sufficient.

7.1.2

Terminal assignment

Connection is solely by means of device plug →  25.

Содержание Dosimag













































































Результаты поиска

Содержание Dosimag

Отзывы:

Похожие инструкции для Dosimag

Бренды по названию

Популярные бренды

Endress+Hauser Dosimag, Руководство по эксплуатации

Результаты поиска

Содержание Dosimag

Отзывы:

Похожие инструкции для Dosimag

Бренды по названию

Популярные бренды