EMC2 AX100 Series Скачать руководство пользователя

Страница: 9 / 68

AX100-Series - Installing a Fibre Channel Storage System with a Direct Connection to a NetWare Server

Installing PowerPath on the Server

Install or Update the HBA

Driver

1. Install any updates, such as hot fixes or patches, to the server’s

operating system that are required for the HBA driver version
you are installing.

2. After installing any updates, reboot the server.

3. Install the driver following the instructions on the HBA vendor’s

website.

4. Reboot the server when the installation program prompts you to

reboot.

Some driver updates may require you to reboot the server.

5. If the installation program did not prompt you to reboot, reboot

the server when the driver installation is complete.

Installing PowerPath on the Server

For

all

configurations you

must

install PowerPath

each

server that

you will connect to the storage system. PowerPath manages the data
paths between the server and storage system.

If PowerPath is already running on the server, do one of the
following:

◆

For a new AX100SC (single-SP) storage system, go to

Unpacking

the Storage System

(page 16).

◆

For a new AX100 (dual-SP) storage system, go to

Installing the

UPS (AX100 Only)

(page 15).

◆

For an existing storage system (that is, one already connected to
another server), go to

Connecting the Storage System to the Server

(page 49).

Before You Start

To complete this procedure, you need to

❑

Locate the PowerPath for NetWare CD that shipped with the
storage system.

Содержание AX100 Series





































































Результаты поиска

Содержание AX100 Series

Отзывы:

Похожие инструкции для AX100 Series

Бренды по названию

Популярные бренды

EMC2 AX100 Series, Руководство пользователя

Результаты поиска

Содержание AX100 Series

Отзывы:

Похожие инструкции для AX100 Series

Бренды по названию

Популярные бренды