EMC2 AX100 Series Скачать руководство пользователя страница 8

Страница: 8 / 68

AX100-Series - Installing a Fibre Channel Storage System with a Direct Connection to a NetWare Server

Installing or Updating the HBA Driver

The server must run a supported HBA driver. For information on the
supported HBA drivers, refer to

Supported Configurations

in the

"Technical descriptions" section on the AX100 support website.

If the server is already running a supported HBA driver, go to

Installing PowerPath on the Server

(page 9)

Read this section for all other configurations.

Before You Start

To complete this procedure, you need

❑

The latest version of a supported HBA driver. You can download
the latest supported version and instructions for installing it from
the HBA vendor’s website.

QLogic HBA website

http://www.qlogic.com/go/emc_approved

The

HBA

driver is also on the installation CD that ships with the

HBA

This version may not be the latest supported version.

❑

Any updates, such as hot fixes or patches, to the server’s
operating system that are required for the HBA driver version
you will install.

For information on any required updates, refer to one of the
following:

•

Supported Configurations

in the "Technical descriptions" section

on the AX100 support website

• The HBA vendor’s website (see above)

Содержание AX100 Series





































































Результаты поиска

Содержание AX100 Series

Отзывы:

Похожие инструкции для AX100 Series

Бренды по названию

Популярные бренды

EMC2 AX100 Series, Руководство пользователя

Результаты поиска

Содержание AX100 Series

Отзывы:

Похожие инструкции для AX100 Series

Бренды по названию

Популярные бренды