Eltroplan REVCON RLD Скачать руководство пользователя страница 78

Страница: 78 / 98

Electrical Installation

Operating instructions RLD 77

ELTROPLAN

REVCON



Elektrotechnische Anlagen GmbH

4.6

Installation of a power feedback unit in a CE-typical drive system

General



The user is responsible for the compliance of his application with the EC

directives

If you observe the following measure you can be sure that the drive system

will not cause any power-feed/feedback-unit-caused EMC problems, i.e.

comply with the EMC

Directive when running the machine.

If devices which do not comply with the CE requirement concerning noise

immunity EN 61000-6-2 are operated close to the power feed/feedback unit,

these devices may be interfered electromagnetically by the power

feed/feedback units.

Assembly



Connect the power feed/feedback unit and the RFI-filter to the grounded

mounting plate with a wire of large cross section as possible:

–

Mounting plates with conductive surfaces (zinc-coated or stainless steel) al-

low permanent contact.

–

Varnished boards should not be used for installation in accordance with

EMC.



If you use several mounting plates:

–

Connect as much surface of the mounting plates as possible (e.g. with copper

bands)



Ensure the separation of power and control cables.



Cable guides as close as possible to the reference potential. Unguided cables

have the same effect as aerials.

Filters



Use RFI filters which are assigned to the power feed/feedback unit.

RFI filters reduce impermissible high frequency interference to a permissi-

ble value.

Screening



Metallic cable glands ensure a big-surface connection between screen and

housing



If the screened wire are interrupted at relays or terminals:

Connect the screens of the wires with a big surface to the mounting plate.



If the mains wires between RFI-filter and power feed/feedback unit are long-

er than 300mm:

Use screened mains wires

Connect the screen direct at the controller / power feed/feedback unit and at

the RFI-filter to the mounting plate.



Screen the control wires:

Connect the screens on the shortest possible way to their terminals.

Earthing



All metallic conduction components (power feed/feedback unit, controller,

RFI-filter) have to be connected to one common earthing point (PE-bus bar).



Observe the in the safety guidelines defined minimum cross sections:

For EMC not the cross section, but the surface of a wire and the contact to

the mounting plate is important for the function.

Содержание REVCON RLD



































































































Результаты поиска

Содержание REVCON RLD

Отзывы:

Eltroplan REVCON RLD, Руководство пользователя, Страница: 78 / 98

Результаты поиска

Содержание REVCON RLD

Отзывы: