manualshive.com logo in svg

Eltroplan REVCON RLD, Руководство пользователя, Страница: 68 / 98

Поделиться
Скачать
Eltroplan REVCON RLD Скачать руководство пользователя страница 68

 

                                                                                                             Electrical Installation 

 

Operating instructions RLD                                                                                            67 

ELTROPLAN

 - 

REVCON



       

Elektrotechnische Anlagen GmbH

 

 

Legend for figure 4.4.1.2 (REVCON

 RLD E0 with RHF-RA) 

1.

 

Fusing in accordance with controller manual. 

2.

 

It is not allowed to connect any other devices except the frequency inverter and the power 
feedback unit behind the main magnetic switch. 

Danger! 

If this is not observed, you take the risk that, in the case of switching off the mains during feed-
back the power, the voltage in that sector may rise up to a dangerous level. This may destroy the 
connected devices and perhaps also the inverter and/or the power feedback unit. To avoid such 
situation, the power feedback unit is equipped with an overvoltage switch off, but nevertheless 
this hint should be observed! 

3.

 

RHF-RA module 

4.

 

Cross section in accordance with the relevant VDE-rules. 

5.

 

Beginning with enclosure 2: Fusing (Supply, <2A current input) in accordance with DIN 
VDE 0298 or short circuit proof wiring. 

6.

 

RFI filter, optional: 

At RFI-filter installation size RFI-RA01 is the connection to the power feedback module 
realized by a PG-screw connection. This connection of the RFI-filter must occur phase 
correct over the terminals -From Supply-. The terminals -To Inverter- must be open.  

7.

 

At these terminals one or more controllers (even with different power ratings) may be at-
tached, like it shown in figure

 

4.5.1. Even if several controllers are attached, the wires 

have to be as 

short and low impedance

 as possible! 

8.

 

DC fuses: The power feedback is not equipped with DC fuses. 

9.

 

The possibility of an external „OFF“ by the terminals 7 and 8: 

     These terminals may be used for an external 

OFF

-signal (NOC, short time contact) to 

stop the power feedback unit. 

10.

 

The „ON“ or „RESET“ signal may be initiated via terminals 11 and 12: 
Terminals 11 and 12: Positive pulse (12-24 V DC); practicable e.g. via PLC (terminal 11 
+, terminal 12 -). 

11.

 

Fan supply: The power feedback modules beginning with enclosure 2/701 require the in 
the ordering code specified auxiliary voltage (230V or 115V). 

 

Содержание REVCON RLD



































































































Отзывы:

Нет отзывов